User manual THOMSON MPC-ETN QUICK INSTALLATION GUIDE

[. . . ] Your IT SUPPORT GROUP must assign a `Static IP Address' to the MPC-ETN. The `Static IP Address' is required so that the MPC-ETN device will work correctly on your Ethernet Network. Modscan32 software is needed for Check/Verification of the MPC-ETN setup. [. . . ] Open the required template project (MEC20 or TSC800) using the Project->Open Project menu. Select `MPC-ETN' found in the `Product Selection' tree. Click the `Open Project' button found in the Tool Bar located at the bottom of the `Gateway' software window. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN Select ET5MEC20-R2. prj for MEC20 communication or ET10TSC800-R2. prj for TSC800 communication, and then Press the OPEN button. 3. To change the default IP and Ethernet address Press the PLC2 button on the Gateway Utility Software toolbar. Click the Advanced button to open the IP edit dialog box. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN Enter the required Modbus Node number (the default node is 1). Press the Extended Setup button for the TCP/IP setup. Enter the TCP/IP information and press the OK button. NOTE: · Your IT SUPPORT GROUP must assign a `Static IP Address' to the MPC-ETN. The `Static IP Address' is required so that the MPC-ETN device will work correctly on your Ethernet Network. 4. Connect the PC end of the programming cable to the PC and connect the MPC-COM1 end of the programming cable to the MPC-ETN COM1 port. 5. Press the Download button of the Gateway Utility Software toolbar. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN Select the appropriate COM port from the combo dropdown list. The green OK light will blink steadily for approximately 10s. This indicates that the MPCETN is in upload/download mode. If the light stops blinking before an upload or a download is conducted then the power to the MPC-ETN must be cycled to put it back into upload/download mode. Click the Select All button then Download. (Cycle power to the MPC-ETN if necessary. ) 6. Once download is complete a confirmation will appear. Set-up complete. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN Connections for Final Configuration: Connecting to MPC-ETN 1. Connect the RJ45 end of Cable 1 to the intended Thomson Technology controller. Connect the MPC-COM1 end of Cable 1 to the MPC-ETN port labeled COM1. Connect MPC-ETN to PC 1. Connect a customer supplied Ethernet cable to the Ethernet port of the MPC-ETN (not the Pass Through port). [. . . ] ping 10. 50. 1. 199) Your system should return something similar to the screen shot on the left if your connection and setup is correct. The test may need additional support from your IT SUPPORT GROUP. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN 3. Open `Modscan32. exe' and follow the procedure below: Select `Connect' for the `Connection' drop down menu. Connect Using: `Remote Modbus TCP Server', Enter IT supplied `Static IP Address', Default listening port `502'. THOMSON TECHNOLOGY 9087A ­ 198 STREET, LANGLEY, BC CANADA V1M 3B1 TELEPHONE: (604) 888-3381 EMAIL: info@thomsontechnology. com www. thomsontechnology. com PM086 REV 1 08/08/28 th Quick Installation Guide for MPC-ETN For MEC20 ­ Enter Address: `1001' Length: `5' '03:HOLDING REGISTER' For TSC800 ­ Enter Address: `6001' Length: `5' '03:HOLDING REGISTER' NOTE: · When comm. /setup/configuration is correct the program will increment both counters (Number of Polls and Valid Slave Responses) at the same rate. [. . . ]