User manual THOMSON ROC2407 SUBCODES

[. . . ] Preprogrammed Set Up Three Digit Code Method Auto Search Method Recalling the Set Up Code Number C. Learning Set Up Learning New Functions on the Main Keypad Learning New Functions on Device Buttons Erasing Learned Functions Erasing Individual Buttons Erasing All Buttons in One Device Mode Erasing All Buttons in All Device Modes D. Operation Device Buttons Main Device Mode Automatic Audio Mode Backlighting Advanced Features A. Punch Through Controls Volume "Punch Through" Channel "Punch Through" Transport "Punch Through" B. [. . . ] The LCD on the ROC2407 will flash GOOD, the DEVICE Mode and then return to LEARN, verifying that the new function has been learned. 16 Using Your Remote 8 Press and hold the DEVICE button and the SEL/PLAY button simultaneously, once again. SAVED will flash three times in the LCD and return to the DEVICE mode, indicating that the programming has been stored. Erasing Learned Functions To erase learned functions, please refer to the following procedures: Erasing Individual Buttons: 1 Press the Device button for the mode where the learned function has been stored. 2 Press and hold the Device and the SEL/PLAY buttons simultaneously, for about 3 seconds, until the LCD shows LEARN. 3 Press and release the button to be erased. The LCD will show READY. 4 Press the LIGHT button. The LCD will flash ERASE, CLEAR, the Device Mode and then return to LEARN. Repeat Steps 3 and 4 for any other buttons to be erased. 5 To return to the normal operating mode, press the Device and the SEL/PLAY buttons simultaneously. The learned functions on the selected buttons have now been erased. The preprogrammed functions for these buttons will now operate on the remote control. 17 Using Your Remote Erasing All Buttons in One Device Mode: 1 Press the Device button for the mode to be erased. 2 Press and hold the Device and SEL/PLAY buttons simultaneously, for about 3 seconds, until the LCD shows LEARN. 3 Press and hold the Device and LIGHT buttons simultaneously for approximately five seconds and then release the buttons. The LCD will flash ERASE and then alternately CLEAR and the Device Mode. Note: When the LCD on the remote returns to the Device Mode, all the learned functions in the selected Device mode have been erased. All the buttons in that Device mode will now operate with the preprogrammed functions in that mode. Every time that the Device button is pressed it will also emit the joined function. To erase a joined function from a Device button: 1 Press the AUDIO and ENTER buttons simultaneously on the remote control. JOIN will appear in the LCD. 2 Press the Device button that you would like to erase a joined function. CLEAR will flash and INPUT will then appear in the LCD. 3 Press the ENTER button. The LCD will flash SAVE twice and return to AUDIO indicating that the join has been erased. Main Device Mode When the main device is displayed in the LCD, the ROC2407 will perform all of the preprogrammed, joined, learned and punch through features for that device mode. Automatic Audio Mode The remote is defaulted to the Automatic Audio. When the remote control is in this mode, pressing a Device button a second time will display A_XXX in the LCD indicating that the Volume and Mute controls of the device programmed into the Audio mode of the ROC2407 is active, while full function control of all other buttons of the current Device mode is maintained. Main Device Mode Automatic Audio Mode 21 Using Your Remote No IR commands are emitted during the second press of a Device button when the remote is in the Automatic Audio mode. Pressing the Device button again will return the remote to the Main Device Mode. To Delete the Automatic Audio for a Device mode: 1 Press and hold the AUDIO Device button and the LIGHT button simultaneously. A_SET will appear in the LCD. 2 Press the Device button corresponding to the Device mode to be deleted for Automatic Audio. A_OFF will appear in the LCD indicating the deleted status of the automatic Audio mode for the Device mode. 3 Press the ENTER button to store the programming. SAVE will flash in the LCD and then return to AUDIO. To Return to Automatic Audio for a Device mode: 1 Press and hold the AUDIO Device button and the LIGHT button simultaneously. [. . . ] If it does not turn off, select the next Set-Up Code number from the table, and press in that code number. When your device turns off, proceed to Step 6. 6 Press the Device Button that was selected in Step 2. to store the Set-Up Code number. PASS will flash in the LCD to confirm the programming. The second device can now be operated by pressing the assigned Device Button and using the buttons within this mode. 34 Warranty The Home Theater Master ROC2407 remote control comes with a one-year warranty from the date of purchase. Specifications Model ROC2407, infrared remote control. [. . . ]