User manual THOMSON TSC 800 V2.1

[. . . ] TSC 800 TRANSFER SWITCH CONTROLLER INSTALLATION, OPERATING & SERVICE MANUAL Software Version 2. 1 PM049 REV 9 06/04/24 9087A ­ 198 Street, Langley, BC Canada V1M 3B1 Telephone (604) 888-0110 Telefax (604) 888-3381 E-Mail: info@thomsontechnology. com www. thomsontechnology. com th 9087A ­ 198 Street, Langley, BC Canada V1M 3B1 Telephone (604) 888-0110 Telefax (604) 888-3381 E-Mail: info@thomsontechnology. com www. thomsontechnology. com th TSC 800 TRANSFER SWITCH CONTROLLER TABLE OF CONTENTS 1. PRODUCT REVISION HISTORY GENERAL DESCRIPTION 1 1 2 2. INSTALLATION 2. 1. GENERAL INFORMATION NOTES TO INSTALLER AC VOLTAGE SENSING INPUT AC CONTROL POWER INPUT OUTPUTS SYSTEM PHASING-HIGH LEG DELTA SYSTEMS EXTERNAL PANEL CONTROL WIRING REMOTE START CONTACT FIELD WIRING COMMMUNICATION CABLE DIELECTRIC TESTING 5 5 5 6 6 7 7 10 10 11 12 3. DESCRIPTION 3. 1. LEXAN FACEPLATE 12 12 14 14 15 15 16 16 3. 2. [. . . ] 0-23 hour) that the generator set is to be stopped following its exercise period. 7. 2. 7. AUTO TEST STOP MINUTE Select the minute of the day (e. g. 0 to 59 minutes) that the generator set is to be stopped following its exercise period. 7. 2. 8. AUTO TEST MODE Select type of test mode desired. Three test modes are available as follows: Auto: Off Load: The exercise test mode is de-activated The generator set will be started during the exercise period but no transfer will occur. NOTE: The generator will transfer on load if the utility supply fails during the test period. On Load: The generator will be started and will transfer on load. NOTE: During the On-Load exercise test mode, the transfer switch will automatically re-transfer back to the utility supply if the generator set fails. 7. 3. SYSTEM CONFIGURATION The TSC 800 controller provides a flexible control system to allow specific operation for a wide range of power distribution types. To program the system configuration, refer to the following descriptions: 7. 3. 1. FIRMWARE VERSION "Display Only" - The Controller's current firmware version number and date of release. PM 049 REV 9 06/04/24 44 Thomson Technology TSC 800 TRANSFER SWITCH CONTROLLER 7. 3. 2. ATS MODE MENU PASSWORD (PW) NOTE: The following features is provided in TSC 800 Software version 2. 0 (or higher). Viewable only in Master Read / Write Mode. Allows setting of Password Protection restricting access to the ATS Mode Menu as follows: ENABLED: Access to initiating/changing any test or operation mode requires a userentered password. The password required will be the same as a level 2 (e. g. DISABLED: The ATS Mode Menu may be entered and changes made/initiated without the use of a security password. 7. 3. 3. UTILITY FAIL CALLOUT NOTE: The following features are viewable only in Master Read / Write Mode in TSC 800 Software version 2. 0 (or higher). When the remote communication option is enabled, this programming prompt will appear. This feature may be enabled or disabled by programming selection. ENABLED: The controller will initiate a callout signal via the communication port to a remote connected device when a Utility (Source 1) power failure is detected. The callout signal will be reset when the Utility (Source 1) power returns to normal condition. DISABLED: The controller will not initiate a callout when a Utility (Source 1) power failure is detected. 7. 3. 4. LOAD ON GENERATOR CALLOUT When the remote communication option is enabled, this programming prompt will appear. This feature may be enabled or disabled by programming selection. ENABLED: The controller will initiate a callout signal via the communication port to a remote connected device when the load is connected to the generator supply. The callout signal will be reset when the load transfers back to the utility supply. DISABLED: The controller will not initiate a callout when the load transfers to the generator supply. PM 049 REV 9 06/04/24 45 Thomson Technology TSC 800 TRANSFER SWITCH CONTROLLER 7. 3. 5. TRANSFER FAIL CALLOUT When the remote communication option is enabled, this programming prompt will appear. This feature may be enabled or disabled by programming selection. [. . . ] Verify the TSC 800 has not been set for a manual or auto off load test operation. If yes, select "Auto" ("None" in firmware versions 1. 7 and earlier). Verify the TSC 800 engine start LED is lit on the rear of the controller. If not lit isolate one of the remote start wires to confirm the start is from the TSC 800 (contact closes to start, open wire should cause generator to stop). [. . . ]