User manual THOMSON TSC 80E V2.1

[. . . ] TSC 80e TRANSFER SWITCH CONTROLLER INSTALLATION, OPERATING & SERVICE MANUAL Software Version 2. 1 PM091 Rev 0 09/01/21 9087A ­ 198 Street, Langley, BC Canada V1M 3B1 Telephone (604) 888-0110 Telefax (604) 888-3381 E-Mail: info@thomsontechnology. com www. thomsontechnology. com th TSC 80e TRANSFER SWITCH CONTROLLER TABLE OF CONTENTS 1. NOTES TO TRANSFER SWITCH INSTALLER 1. 3. 1. SYSTEM VOLTAGE SYSTEM PHASING - HIGH LEG DELTA SYSTEMS REMOTE START CONTACT FIELD WIRING DIELECTRIC TESTING 1 1 2 2 2 3 4 4 2. DESCRIPTION 2. 1. DIAGNOSTIC LED'S 5 5 7 8 8 2. 3. [. . . ] USER READ (VIEW ONLY MODE) User can view any programming parameter as required. No Password is required for the VIEW ONLY MODE. To enter the VIEW ONLY MODE to review programming settings, follow the procedure as listed below: 1. Press the DOWN or UP keys to scroll through the available programming menus. Once the selected program menu is displayed, press the ENTER key to view the sub-menus available. Press the DOWN or UP keys to scroll through the programming sub-menus available. Once the selected program sub-menu item is displayed, press the ENTER key to view the selected value. To exit the programming sub-menus, press the ESC key. To exit back to the normal display mode, press the ESC key again. 4. 1. 2. USER READ / WRITE MODE User password can view and modify all programming parameters except submenu items "Clear System Statistics", "Clear Data Log", "Set Voltage Calibrations" & "System Options". User password can also modify the User password number. The Factory default number for the User read/write mode is one (01). MASTER READ / WRITE MODE Master password can view and modify all programming parameters except items in the "System Options" sub-menu. Master password can also modify the User password number. Consult THOMSON TECHNOLOGY factory for master password number if required. PM091 Rev 0 09/01/21 27 Thomson Technology TSC 80e TRANSFER SWITCH CONTROLLER 4. 1. 4. PASSWORD ENTRY PROCEDURE To enter the programming mode, follow the procedure as shown: 1. Press the ENTER key to obtain the Password Main Menu. The "PASSWORD ENTRY & RESETS" prompt will appear). Press the ENTER key a second time to obtain the Password Sub Menus. The "USER PASSWORD" prompt will appear). If the USER password is to be entered, proceed to step #4. Press the DOWN arrow key to select USER or MASTER password sub-menu 4. [. . . ] MAX. A (L1) 27 1 34 UTILITY SUPPLY SENSING 120-600VAC 50/60Hz 3 PHASE 1 B (L2) 2 33 PROG #3 FAIL TO TRANSFER (DEFAULT) RATED 10A, 120/250VAC, 5A, 30VDC RES. MAX. C (L3) 3 32 37 A (L1) 4 36 PROG #2 LOAD DISCONNECT CONTACT (DEFAULT) RATED 10A, 120/250VAC, 5A, 30VDC RES. MAX. GENERATOR SUPPLY SENSING 120-600VAC 50/60Hz 3 PHASE 1 35 B (L2) 5 31 C (L3) 6 30 PROG #1 ATS NOT IN AUTO (DEFAULT) RATED 10A, 120/250VAC, 5A, 30VDC RES. MAX. 29 A (L1) 7 16 15 LOAD SENSING 120-600VAC 50/60Hz 3 PHASE 2 B (L2) 8 14 PROG #4 LOAD ON GENERATOR (DEFAULT) RATED 10A, 120/250VAC, 5A, 30VDC RES. [. . . ]