User manual TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598. We hope that this TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598 user guide will be useful to you.
Lastmanuals help download the user guide TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598.
Manual abstract: user guide TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598
Detailed instructions for use are in the User's Guide.
[. . . ] When wiring is completed, check all components by running system through its entire heating cycle. All vent system leaks must be sealed prior to the installation of the Draft Inducer. Flue gas temperature must not exceed 575o F at Draft Inducer inlet.
MODELS D3 AND AD-1 MOTOR REPLACEMENT (DIAGRAM A)
1. [. . . ] If appropriate circuit does not appear, consult Tjernlund Products, Inc. All wiring must be done in accordance with the NEC and applicable codes. The wiring from the appliance should be protected by overcurrent protection(fuses or circuit breakers) rated 15 amperes or less, as applicable for 14 AWG conductors. EXTREME CAUTION MUST BE EXERCISED TO ENSURE THAT WIRING DOES NOT COME INTO CONTACT WITH ANY HEAT SOURCE. Check heater and Draft Inducer operation. Vari-Draft control on Draft Inducer should be adjusted so that there is no spillage at draft diverter, hood or barometric.
DIAGRAM A
MODELS AD-1 D-3
IN-FORCER PAI-1 & 2 SERIES WITH DATE CODES AFTER "9704" (DIAGRAM B)
1. Remove (6) screws from bottom front and sides of IN-FORCER while holding blower assembly firmly. Carefully slide blower assembly down until stops hold blower unit in place. Remove nuts which attach motor mount to housing. Remove motor/mount assembly and remove defective motor. NOTE: USE CARE SO FASTENERS ARE NOT LOST. Firmly fasten motor to motor mount using proper spacers, washers and nuts removed in step 4. Insert motor shaft into IN-FORCER wheel and attach motor/mount assembly to housing with nuts removed in step 4. Secure IN-FORCER wheel by tightening set screw onto flat of motor shaft. Spin the wheel by hand to ensure proper alignment and equal wheel clearance on both housing sides. Slide blower assembly back into housing and replace (6) screws removed in step 1. [. . . ] Secure wheel by tightening set screw onto motor shaft. Spin the wheel by hand to ensure proper alignment and equal wheel clearance on both housing sides. for IN-FORCER casing and replace motor stud nut. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-3022 MOTOR KIT 8504066 REV 1 0598 will begin.
