User manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196. We hope that this TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196 user guide will be useful to you.

Lastmanuals help download the user guide TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196.

Mode d'emploi TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196

Download

Manual abstract: user guide TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196

Detailed instructions for use are in the User's Guide.

 [. . . ] TJERNLUND PRODUCTS,  INC. 
1601 Ninth Street · White Bear Lake,  MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com

MODEL I,  IL,  XL REPLACEMENT MOTOR KIT

1. Disconnect power supply before making wiring connections to prevent electrical shock and equipment damage.  [. . . ] 3 Loosen set screw(s) which attach shaft extension to motor shaft. Insert shaft extension onto new motor shaft. Secure shaft extension by tightening set screw(s). To ensure proper performance and extended bearing life of the motor,  inspect wheel and clean if necessary. Refer to the installation instructions of your unit for proper maintenance procedures. Position motor onto motor mount,  being sure motor shaft (with shaft extension) is fitted into Draft Inducer wheel. Firmly fasten motor to motor mount with wrench,  using proper bolts,  washers and nuts removed in step 2. Secure Draft Inducer wheel by tightening set screw(s) onto shaft extension. Spin the wheel by hand to ensure proper alignment and equal blade clearance on both housing sides. Wire Draft Inducer according to appropriate diagram on back. If appropriate circuit does not appear,  consult Tjernlund Products,  Inc. All wiring must be done in accordance with the NEC and applicable codes.  [. . . ] Oil holes or lances are provided at front and rear faces of motor. 

GAS WIRING TO ANY APPLIANCE EQUIPPED WITH 24V CONTROLS NO POST-PURGE RELAY/TIMER ON DRAFT INDUCER

COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 24/115V RELAY USE 950-1040 FOR MODELS DJ3 & D3 USE 950-1016 FOR MODELS I,  IL,  XL

DRAFT INDUCER CONNECTED TO OIL BURNER WITH R8184G CONTROLS (DRAFT INDUCER MOTOR LESS THAN 4. 4 AMPS) INCLUDES MODELS UP TO THE D3

COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 950-1067 RELAY/TIMER MAXIMUM AMP LOAD IS 4. 4 AMPS USE DIAGRAM BELOW IF DRAFT INDUCER MOTOR IS GREATER THAN 4. 4 AMPS

DRAFT INDUCER CONNECTED TO OIL BURNER WITH R8184G CONTROLS (DRAFT INDUCER MOTOR GREATER THAN 4. 4 AMPS) INCLUDES THE MODELS I,  IL,  XL

COMPONENTS NEEDED: (1) DRAFT INDUCER (1) PS1505 FAN PROVER (1) 950-1067 RELAY/TIMER MAXIMUM AMP LOAD IS 4. 4 AMPS (1) HONEYWELL R4222B1082 RELAY OR EQUIVALENT (INSTALLER SUPPLIED)

REV. 2,  11/96

© 1996 TJERNLUND PRODUCTS,  INC. 

P/N 8504051 [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND 950-4020 I, IL, XL MOTOR KIT 8504051 REV 2 1196 will begin.