User manual TJERNLUND SS1R SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.06) 8504117 REV B 0206

[. . . ] B 02/06 TJERNLUND PRODUCTS, INC. 1601 Ninth Street · White Bear Lake, MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com UC1 VERSION X. 06 THIS VENT SYSTEM HAS BEEN LISTED FOR USE WITH SPECIFIED RHEEM, RUUD, WEATHERKING AND HEAT CONTROLLER OIL FURNACES BY UL AND ULC. SEE FURNACE RATING PLATE FOR VERIFICATION. INCLUDES UC1 UNIVERSAL CONTROL MODEL SS1R INSTALLATION INSTRUCTIONS !Recognize this symbol as an indication of important Safety Information! OWNER INSTRUCTIONS, DO NOT DESTROY NOTE: FLUE GAS TEMPERATURES MUST NOT EXCEED 575oF AT VENT SYSTEM INLET. THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED, LICENSED SERVICE PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND OPERATION OF THIS UNIT. READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING INSTALLATION OR OPERATION. [. . . ] In addition to L1, Neutral and ground that must be supplied to the SS1R UC1 control board, five wires are to be installed from the oil furnace to the SS1R Side Wall Vent System. Refer to Diagram R wiring instructions below. Attach L1 (115V) and Neutral wires from a nominal 115VAC power source to L & N on the SS1R UC1 control board. This power should be routed through a disconnect so that power to the SS1R can be turned off remotely if necessary. Additionally, all wire should be run through the appropriate conduit per NEC standards as noted in step 1. A ground wire will need to be supplied between the system ground and the grounding lug in the SS1R electrical box. A neutral wire will need to be installed from the oil furnace line neutral to the terminal labeled "2" on the UC1 control board. Inside the burner mounted junction box, remove the leads from the primary control terminals labeled "Burner/Motor" and "Valve". Install a field-constructed wire between the lead removed from the terminal labeled "Burner/Motor" (step E above) and the UC1 control board terminal labeled "M". The connection to the burner motor lead will require a special male ¼" quick connect (Amp Manufacturing part # 2-520102-2 (insulated male spade)). Do NOT cut any wires on the existing burner. Also, the wire connection to the "Burner/Motor" lead should be made inside the burner junction box and should be covered and concealed by the primary control once it is replaced. Install a field-constructed wire between the terminal labeled "Burner/Motor" (step E above) and the UC1 control board terminal labeled "1". The connection to the primary control will require a female ¼" quick connect (Amp Manufacturing part # 2-520856-2). Install a field-constructed wire between the lead removed from the terminal labeled "Valve" (step E above) and the UC1 control board terminal labeled "4". The connection to the "Valve" lead will require a special male ¼" quick connect (Amp Manufacturing part # 2-520102-2 (insulated male spade)). Do NOT cut any wires on the existing burner. Also, the wire connection to the "Valve" lead should be made inside the burner junction box and should be covered and concealed by the primary control once it is replaced. Install a field-constructed wire between the terminal labeled "Valve" (step E above) and the UC1 control board terminal labeled "3". The connection to the primary control will require a female ¼" quick connect (Amp Manufacturing part # 2-520856-2). IMPORTANT: The Call Jumper between J1 and J2 on the UC1 board in SS1R must be removed. The RED Voltage Jumper on UC1 board must be in the 115V position. C. [. . . ] If unable to determine faulty component, contact your Tjernlund distributor or Tjernlund Products Technical Customer Service Department at 1-800-255-4208 for troubleshooting assistance. 2. ) After the faulty component is determined, return it to your Tjernlund distributor for replacement. Please include SS1R date code component was taken from. The date code is located on the Electrical Box cover plate. [. . . ]