User manual TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705. We hope that this TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705 user guide will be useful to you.

Lastmanuals help download the user guide TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705.

Mode d'emploi TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705

Download

Manual abstract: user guide TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705

Detailed instructions for use are in the User's Guide.

 [. . . ] TJERNLUND PRODUCTS,  INC. 
1601 Ninth Street · White Bear Lake,  MN 55110-6794 PHONE (800) 255-4208 · (651) 426-2993 · FAX (651) 426-9547 Visit our web site · www. tjernlund. com

IMPORTANT!!!UC1 BOARD VERSION X. 06 UPDATES
NEW X. 06 VERSION UC1 BOARD FEATURES
IMPORTANT: This upgraded circuit board features: A new #6 power LED Constant red when 115 VAC is supplied to L & N. A new color for the #2 LED Constant blue when fan prover safety circuit is closed.  [. . . ] Keeping the Pre-Cycle Prover Status Check activated may cause nuisance lockouts. Important: Deactivate the Pre-Cycle Prover status check if installing this board on a new or existing draft inducer installation by pushing the #9 dip switch up or "ON" to disable. 

LED INDICATOR LIGHTS LED #1 (Amber) Appliance call for heat. LED #2 (Blue) Safety circuit through P1 & P2 (Venter Fan Prover and/or High Limit). Indicates Venter prover is closed during run cycle. Burner circuit is energized with Interlock Relay contact closure from terminal 3 to 4. LED #3 (Green) Power switched to Venter motor from L to MTR & M. LED #5 (Red) Used as a status indicator. LED #6 (Red) 115 VAC power supplied to board. 

P/N: 8505017

©2005 TJERNLUND PRODUCTS,  INC. B 07/05

LED STATUS INDICATORS LED #4 & #5 (Red) Flashing Alternately LED #4 & #5 (Red) Flashing in Unison LED #4 Flashes Continuously* LED #5 (Red) Flashing Intermittently LED FAULT INDICATORS Fault conditions are indicated by counting the number of times LED #4 (Red) flashes. LED #4 Flashes 2 Times LED #4 Flashes 3 Times* LED #4 Flashes 4 Times* LED #4 Flashes 5 Times* Fan Prover was in electrically closed position prior to venter operation. Fan Prover does not close within 60 seconds after call for heat. Fan Prover did not re-close after 10 minutes of Venter operation. Fan Prover opened for more than 10 seconds during burner cycle but closed within 10 minutes. (Pre-Purge options 0,  5,  20,  35 seconds) = Venter in Post-Purge. (Post-Purge options 0,  30 seconds or 1,  2,  4,  8,  16 minutes) = Fan Prover opened for more than 10 seconds during burner cycle. (Venter will run for 10 minutes,  attempting to make Fan Prover) = With no call for heat,  flashes 3 seconds on / 3 seconds off if microcontroller is working properly. 

* Investigate cause of Fan Prover short cycling such as; Firing burner at capacities or temperatures exceeding Venter limits,  excessive vent pipe runs,  elbows directly on venter discharge,  high winds,  plugged / kinked Fan Prover sensing tube or a faulty Fan Prover switch.  [. . . ] The last fault code,  or lack there of,  will be indicated by counting the number of times LED 4 flashes. By moving any of the dip switches back to their original position,  the fault code will be cleared. NOTE: The UC1 board must have its 115 VAC power supply present when any of the (1-8) dip switches are moved back to their original position for the fault code to clear.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual TJERNLUND UC1 UNIVERSAL CONTROL (VERSION X.06) ADDENDUM 8505017 REV B 0705 will begin.