User manual TJERNLUND VP-2, VP-3 MILLIVOLT WATER HEATER VENT SYSTEMS 8500567 REV. B 0702

[. . . ] A 01/00 Copyright © 2000, Tjernlund Products, Inc. All rights reserved. P/N 8504025 Tjernlund Products welcomes your comments and questions. Address all correspondence to: Customer Service, Tjernlund Products Inc. , 1601 Ninth Street, White Bear Lake, MN 55110-6794 or email us at fanmail@tjfans. com. TABLE OF CONTENTS In The Event of a Pilot Outage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Typical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Actuation and Safety Controls Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Gas Solenoid Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Gas Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Linear Limit Spillage Sensing Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 Vent Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Code Restrictions & Termination Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Vent Hood Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Venter Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Code Requirements and Installation Restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Plan the vent system layout to avoid the possibility of accidental contact with wiring or plumbing inside of walls. Installation must be done by one experienced and familiar with venting of combustion appliances. o 5 VENT HOOD INSTALLATION 1. Verify that proposed Vent Hood location will conform to "Vent Hood Termination Clearances" on page 5. Use scissors to detach Vent Hood Mounting Template on page 14. Follow instructions on Vent Hood template. POWER VENTER INSTALLATION CODE REQUIREMENTS Power Venter installation must be in accordance with the following requirements of the National Fuel Gas Code: (ANSI Z223. 1) · All portions of the vent system under positive pressure during operation (on the outlet side of the Power Venter) shall be designed and installed so as to prevent leakage of flue or vent gases into a building. · All appliances must enter the vent system on the inlet side of the Power Venter. · Provision shall be made to interlock the appliance(s) to prevent the flow of gas to the main burners when the draft system is not performing so as to satisfy the operating requirements of the equipment for safe performance. Power Venter should be installed as close to the termination of the vent system as possible to prevent flue gas leakage. Power Venter must be installed with the motor shaft horizontal to prevent motor bearing wear. Six inch clearance must be maintained to combustible materials. The Power Venter operates on 110/115 VAC, therefore a grounded outlet must be within reach of the six foot power cord supplied with Power Venter. The flexible power cord supplied with the unit may only be used where local codes permit. If local codes do not permit the use of flexible power cord, follow steps below. Remove the electrical box cover, flexible cord and strain relief from the enclosure. Install suitable conduit fitting in enclosure and splice field wiring into existing wiring using code authorized method (wire nuts, etc. ). Replace electrical box cover. 7 TYPICAL INSTALLATION ACTUATING AND SAFETY CONTROL CIRCUIT CONNECTIONS 1. Push the black lead from the 6' 18/2 cable onto the common terminal of the gas pressure switch. Push the remaining black lead from the 6' 18/2 cable onto one of the terminals on the solenoid valve. Push the yellow lead from the 25' control cable onto the remaining terminal on the solenoid valve. Push the red lead from the 25' control cable onto the piggyback terminal joined with common on the gas pressure switch. Push the blue lead from the 25' control cable onto the normally open terminal on the gas pressure switch. [. . . ] The date code is located on the Electrical Box coverplate. If Power Venter date code is older than 18 months you will need to provide a copy of the original installation receipt to your distributor. Credit or replacement will only be issued to a Tjernlund distributor after the defective part has been returned prepaid to Tjernlund. REPLACEMENT PARTS LIST TJERNLUND LIMITED ONE YEAR WARRANTY ITEM PART NUMBER VP-2 Vent Hood VH1-3 VP-3 Vent Hood VH1-4 VP-2 Venter Motor 950-2020 VP-3 Venter Motor 950-1020 24V Solenoid Valve 950-2040 Gas Pressure Switch 950-2080 24V Transformer 950-2030 Post Purge Relay/Timer (approx. [. . . ]