User manual TNB ANINLAQ46

[. . . ] 3-20 INSTALLING THE SOFTWARE Natural Color . 4-3 TROUBLESHOOTING Monitor Self-Diagnosis . 5-3 MORE INFORMATION Specifications . 6-33 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) . [. . . ] Users can set the <Customized Key> to one of the following functions. If the user presses the Customized Key [ ] after setting it, the configured function will be performed · < Angle> - < Bright> - <Eco Saving> - <Image Size> You can set the function of the Customized Key by selecting <SETUP&RESET > -> <Customized Key> in the OSD. / Use these buttons to navigate the menu or to adjust a value in the OSD. Use this button to control the brightness of the screen. 3-19 Using the product ICON Use this button to select a function. If you press the [ DESCRIPTION ] button when there is no OSD, the input signal (Analog/DVI or Ana- log/HDMI) is switched. When the input signal is switched by pressing [ ] button or the product is turned on, a message displaying the selected input signal appears at the top left of the screen. This function is not available for products with an Analog interface only. Press [AUTO] button to adjust the screen settings automatically AUTO This function is only available in Analog mode. If the resolution settings are changed in the Display Properties, the AUTO adjustment function is performed. Press this button to turn the product on or off · · The buttons on the right of the product are touch-type buttons. Touch the buttons lightly with your finger. Power LED This LED is turned on when the product works normally. - Select when viewing from a slightly lower position. - Select when viewing from the lower position. -Select when viewing from the upper position. <Lean Back Mode1> <Lean Back Mode2> <Standing Mode> <Side Mode> - Select when viewing from the left or right position. , , position at the same <Group View> - Select when two or more persons view among time. Angle · <Custom> -When <Custom> is selected, settings for <Lean Back Mode 1> is applied by default. Users can set suitable picture quality as needed. · · This menu is unavailable when < mode. This menu is unavailable when < Bright> is set to <Dynamic Contrast> or <Cinema> Color> is set. Removes vertical noise lines (line pattern) from the screen. Coarse The location of the screen may be changed after the adjustment. In this case, move the screen so that the screen is displayed at the center of the display panel using the <H-Position> menu. This function is only available in Analog mode. Removes horizontal noise lines (line pattern) from the screen. Fine If you cannot remove the noise completely with the <Fine> function, adjust the <Coarse> and then use the <Fine> function again. [. . . ] Use the software utility installed on your computer to set up this feature. STATE Power Indicator Power Consumption NORMAL OPERATION On 30 watts POWER SAVING MODE Blinking Typical 0. 3 watts POWER OFF Off Typical 0. 3 watts If there is no power cut-off switch, the power consumption is "0" only when the power cord is disconnected. 6-28 More Information 6-29 Specifications MODEL NAME Size Panel Display area Pixel Pitch Synchronization Display Color Resolution Optimum resolution Maximum resolution Horizontal Vertical 24 inches (61 cm) 531. 36 mm(H) X 298. 89 mm(V) 0. 27675 mm (H) x 0. 27675 mm (V) 30 ~ 81 kHz 56 ~ 75 Hz 16. 7M 1920x1080@60Hz 1920x1080@60Hz RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB Input Signal, Terminated 0. 7 Vp-p ± 5% separate H/V sync, Composite, SOG TTL level (V high 2. 0V, V low 0. 8V) Maximum Pixel Clock Power Supply 164MHz (Analog, Digital) This product supports 100-240 V. Since the standard voltage may differ from country to country, please check the label on the back of the product. 15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable 569 x 342 x 53 mm (22. 4 x 13. 5 x 2. 1 inches) (Without Stand) 569 x 416 x 197 mm (22. 4 x 16. 4 x 7. 8 inches) (With Stand) / 3. 4 kg (7. 5 lbs) Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity :10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing -1. 0°(±2. 0°) ~20. 0°(±2. 0°) S24B300B Signal Cable Dimensions (WxHxD) / Weight Environmental considerations Tilt Operating Storage Design and specifications are subject to change without prior notice. Class B (Information Communication equipment for residential use) This device is registered for EMC requirements for home use (Class B). [. . . ]