User manual TNB COMPACT CHARGER CHBA035436

[. . . ] The "Caution, hot surface" symbol indicates that the marked item may be hot and should not be touched. The "Electro Static Discharge (ESD) warning" symbol indicates that trouble (including equipment malfunction) due to static electricity may occur in certain conditions. The "OFF/ON" symbol indicates connection to or disconnection from the mains, at least for mains switches. The "Alternating current" symbol indicates that the equipment is suitable for alternating current only. TROUBLESHOOTING OTHERS CONTENTS CAUTION: NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. [. . . ] Install the print paper to this printer. Install the ink ribbon to this printer. (See page 10. ) FEATURES (See pages 11 to 12. ) (See pages 13 to 14. ) PREPARATION Connect the printer to a personal computer. For CP-D707DW, setting up procedure in the frame is required for each printing unit. Make sure to close the printing unit when the setup procedure is completed. (See page 16. ) TROUBLESHOOTING OTHERS CONTENTS 9 BEFORE OPERATION POSITIONING OF ADJUSTABLE PAPER GUIDE PRECAUTIONS Adjust the paper guides according to the paper width. Adjustable paper guides FEATURES For 9x13(3. 5x5") or 13x18(5x7") size paper (5"-width) For 10x15(4x6") or 15x20(6x8") size paper (6"-width) HOW TO SET THE ADJUSTABLE PAPER GUIDES Pinch the tab on the adjustable paper guide and slide it right or left. Tab PREPARATION TROUBLESHOOTING Slide the paper guide until it stops. Slide other paper guide in the similar way. NOTE Make sure to set the adjustable paper guides to the size of the paper width. When they are not positioned properly, a malfunction such as paper jam and misaligned printing position may occur. NOTE Do not use 10x15 (4x6") or 15x20 (6x8") size paper (having width of 152 mm) after using 9x13 (3. 5x5") or 13x18 (5x7") size paper (having width of 127 mm) for a long time or printing such paper in large quantities. OTHERS CONTENTS 10 BEFORE OPERATION PRINT PAPER INSTALLATION PRECAUTIONS Spacers See the Quick Setup Guide on how to use the spacers. Spacer Paper flange Latch How to attach the spacers 1. Insert the spacer with the paper flange's stoppers retracted. Turn the spacer until the latches are locked. When you remove the spacers from the paper flanges, follow the above procedure in reverse. FEATURES PREPARATION Attachthesuppliedpaperflangestobothsidesoftheprint paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Select a place that is free of dust when loading the ink ribbon. Dust or dirt settling on the ink ribbon results in poor print quality. Make sure that the shafts of the ink ribbon fit into the ink cassette firmly. FEATURES Make sure to load it in the correct position. 3 4 Load the ink ribbon in the ink cassette as shown below. 3 4 Ditch 1 2 1 2 PREPARATION Shaft Ink ribbon Handle Ink cassette Make sure to set the ink ribbon roller to the ditches firmly. Turn the shaft to eliminate any slack. TROUBLESHOOTING Guides Place the ink cassette containing the ink ribbon in the position as shown in the illustration. To insert the ink cassette, align the protrusions on both sides of the cassette with the right and left guides inside the printing unit and slide it in a slanting direction. Mount the ink cassette to the back firmly by holding the handle. Fingerprints or dust on the thermal head will degrade the print quality. Handle CAUTION Do not touch the thermal head right after printing because it is extremely hot. Otherwise you may get burned or injured. NOTE Note that the thermal head is quite sensitive to static electricity. When you touch the thermal head while carrying static electricity on your body, the thermal head may be damaged. OTHERS Protrusion CONTENTS 13 BEFORE OPERATION Close the printing unit by pushing the right and left sides of the unit from the front with both hands. When a new paper is loaded and the printing unit is closed with the power turned on, the paper will be automatically fed and cut. [. . . ] If the ink ribbon, print paper, or ink cassette can not be taken out, consult with your dealer. 20 CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer's life. Wearing gloves at cleaning is recommended to prevent injury. Make sure to turn off the power before cleaning. PRECAUTIONS FILTER CLEANING Clean the filter part and the ventilation inlet with a vacuum as shown right. Ventilation inlet Filter (inside) THERMAL HEAD CLEANING Press the OPEN button to open the printing unit. Take the ink cassette out of the printer. [. . . ]