User manual TOPCOM BALANCE

[. . . ] Important To use `Caller ID' (display caller), this service has to be activated on your phone line. Normally you need a separate subscription from your telephone company to activate this function. If you don't have the Caller ID function on your phone line, the incoming telephone numbers will NOT be shown on the display of your telephone. BALANCE The features described in this manual are published with reservation to modifications. To be connected to the public analogue telephone network. The CE symbol indicates that the unit complies with the essential requirements of the R&TTE directive. This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC. The Declaration of conformity can be found on: http://www. topcom. net/cedeclarations. asp USER GUIDE V1. 0 - 06/08 This product works with rechargeable batteries only. [. . . ] When the handset is inside the base, the base will not ring during incoming call. So when the handset ring volume is turned off and handset is inside the base, your phone will not ring anymore!1 Enter the menu 2 Select "HANDSET" and confirm. 3 Select "INT RING VOL" to change the internal volume or "EXT RING VOL" to change the external volume and confirm. 4 Select a volume (1 to 5 or "OFF"). 5 Confirm or return to the previous menu. 14 Personalize the handset 6. 2 Choosing the ring melody English The base and each handset can ring with a different melody. The handsets can ring with a different melody according to whether the call is internal or external. You can choose from 10 different ringer melodies: 1 Enter the menu 2 Select "SETUP" and confirm. 3 Select "HANDSET" and confirm. 4 Select "INT MELODY" to change the internal melody or "EXT MELODY" to change the internal melody and confirm. 6 Press the OK key to confirm or return to the previous menu. 6. 3 Activation/deactivation of beeps The handsets can emit a beep tone when a key is pressed, when the batteries are low or when the handset is out of range. Key pressed beep tone on/off 1 2 3 4 5 Low battery 1 2 3 4 5 1 2 3 4 5 Enter the menu Select "HANDSET" and confirm. Select "LOW BATTERY" and confirm. Select "ON" to activate or "OFF" to deactivate and confirm. Enter the menu Select "HANDSET" and confirm. Select "ON" to activate or "OFF" to deactivate and confirm. Handset out of range Enter the menu Select "HANDSET" and confirm. Select "OUT RANGE" and confirm. Select "ON" to activate or "OFF" to deactivate and confirm. 6. 4 Handset name You can change the name displayed on the handset (max. This function allows you to personalize each handset. 1 Enter the menu 2 Select "HANDSET" and confirm. 3 Select "NAME" and confirm. 15 Personalize the handset 4GHI 5JKL 6MNO 4 Enter the name you want and confirm. Press the delete key to delete a character. [. . . ] 5 Select "INBOX" or "PERSONAL SMS" and confirm. 7 Confirm or cancel. 23 English Troubleshooting 10 Troubleshooting Symptom No display Possible cause Batteries uncharged Solution Check the position of the batteries Recharge the batteries Turn on the handset Check the telephone cord connection Wait until the other handset hangs up Bring the handset closer to the base Check the mains connection to the base Register the handset on the base Adjust the ringing volume Adjust the dialing mode (pulse/tone) Change the flash time No tone Handset turned off Telephone cord badly connected The line is occupied by another handset Handset out of range The base has no power supply The handset is not registered on the base The ringing volume is off or low The dialing mode is wrong The icon flashes Base or handset do not ring Tone is good, but there is no communication Not possible to transfer a call The flash time is too short or too on PABX long Telephone does not react Manipulation error Remove the batteries and put when pressing the keys them back in place 11 Technical dataTechnical characteristics Standard Frequency range Number of channels Modulation Speech coding Emission power Range Number of handsets Base power supply Handset Batteries Handset autonomy Handset talk time Normal conditions of use Dialing mode Flash time 24 DECT (Digital Enhanced Cordless Telecommunications) GAP (Generic Access Profile) 1880 MHz to 1900 MHz 120 duplex channels GFSK 32 kbit/s 10 mW (average power per channel) maximum 300m in open space / 10-50m in-house Up to 5 230V / 50 Hz / 7, 5V DC 300mA 2 rechargeable batteries AAA, NiMh 1, 2V, 550mAh 200 hours in standby 10 hours +5 °C to +45 °C Pulse / Tone 100 or 250 ms Topcom Warranty 12 Topcom Warranty The Topcom units have a 24-month warranty period. The warranty period starts on the day the new unit is purchased. There is no warranty on standard or rechargeable batteries (AA/AAA type). [. . . ]