User manual TOPCOM COCOON 95

[. . . ] As this telephone cannot be used in case of a power cut, you should use a mains-independent telephone for emergency calls, e. g. This telephone uses rechargable batteries. You have to dispose of the batteries in an environment friendly manner according to your country regulations. DE F AB C 1 Disposal of the device (environment) 1 GH 2 3 MN O I 4 12 5 JKL PQ 5 6 R WX YZ S 7 TU V 8 9 0 4 R/INT M1 At the end of the product lifecycle, you should not throw this product into the normal household garbage but bring the product to a collection point for the recycling of electrical and electronic equipments. The symbol on the product, user guide and/or box indicate this. [. . . ] Enter the desired telephone number or press the Redial key to dial out the number you last called. Press the on-hook button when you want to terminate the call. 5. 1. 2 Call setup with dial preparation Enter the desired telephone number. An incorrect number can be corrected by means of the Mute button. The number will be dialled automatically. Press the Onhook button when you want to terminate the call. 5. 1. 3 Redial one of the last 5 numbers dialled Press the Redial key . The number you last called appears on the display. If you would like to dial one of the last 5 numbers dialled, press the scroll keys a few times until the desired number appears on the display. The number shown on the display is dialled automatically. After finishing your call, press the On-hook key to hang up. 5. 2 Incoming calls to answer the When a call comes in, the handset will start to ring. Press the Off-hook button incoming call. To end the call press the On-hook button. 5. 3 Programming memory numbers You can program 10 indirect numbers (of max. Press any key to stop the ringing on all handsets. 5. 9 Flash button (R) When you press the R button, also called flash or recall, the unit generates a line interruption (of 100 ms or 250 ms). It gives you the possibility to use the special services of your telephone provider and/or to transfer calls when you have a telephone exchange. You can change the flash time if needed (See "Setting the Flash time" on page 6). 5. 10 Programming procedure You can change the ring melodie, volume, day, time etc. . . by going into the program procedure: To go into the program procedure you have to press and hold the Program button until the icon starts to flash. Press the Program button again to change the first setting. Each time you press the Program button you will confirm the previous setting and jump to the next setting: External ring volume/melody Dial mode setting Internal ring volume/melody Date/time setting Flash time setting Base ring volume/melody 5. 10. 1 Handset External melody and volume Press and hold the Program button until the icon starts to flash. Press the Program button again, the external melody is heard and the EXT-icon is flashing. Select the desired melody (1-5) by entering a number (1 - 5). Use the scroll keys to select the desired volume (Off or 1-5) Press again to confirm the setting and to go to the next setting below. 5. 10. 2 Handset Internal melody and volume The internal melody is heard and the INT-icon is flashing. Select the desired melody (1-5) by entering a number (1 - 5). Use the scroll keys to select the desired volume (Off or 1-5) Press again to confirm the setting and to go to the next setting below. Topcom Diablo 100/Twin/Triple/Quattro 5 Topcom Diablo 100/Twin/Triple/Quattro 5. 10. 3 Date time setting After setting the internal ring melody and volume you can set the date and time: DD-MM HH:MM (DD= day, MM=month, HH=houre and MM=minutes) Enter the date and time using the number key. [. . . ] For answered calls the -icon appears and unanswered calls the -icon appears Press the program key to show the other digits (if longer then 12) or to show the date and time. Use the scroll keys to scroll to the previous call. When you reach the top or bottom of the list an error tone will be sounded You can leave the Call list by pressing the on-hook button. 6. 3 Calling a number from the Call list Press the Off-hook Scroll through the Call list until the desired number is shown on the display. The number will be dialled automatically. 6 Topcom Diablo 100/Twin/Triple/Quattro Topcom Diablo 100/Twin/Triple/Quattro 6. 4 Erasing one or all number from the Call list ENGLISH Scroll through the Call list until the desired number is shown on the display. [. . . ]