User manual TOSHIBA 32A42A

[. . . ] Introduction Connecting your TV OWNER'S MANUAL Color Television ® Using the Remote Control Setting up your TV Using the TV's Features 32A32 32A42 32A42A 36A42 © 2002 TOSHIBA CORPORATION All Rights Reserved. TOSHIBA AM E CONSUMER CA P RI TS, INC. DUC RO Appendix O 140 Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. [. . . ] Note: For channels 100 and higher, press the 100 button, and then the next two channel numbers (for example, to select channel 100, press 100, 0, 0; to select channel 125, press 100, 2, 5). 17 Using the TV's features Adjusting the channel settings Switching between two channels You can switch between two channels without entering an actual channel number each time. To switch between two channels: 1. Select the first channel you want to view. Select a second channel using the CHANNEL NUMBERS (0­9 and 100). Every time you press CH RTN, the TV will switch back and forth between the last two channels you tuned the TV to. RECALL MUTE POWER o 1 4 7 100 2 5 8 0 CH 3 6 9 CH RTN CHANNEL NUMBERS ENT CH RTN MENU VOL MENU/ ENTER VOL yz x · Programming your favorite channels The Favorite Channel feature allows you to use the FAV CH buttons on the remote control to cycle through your favorite channels, skipping over channels you do not normally watch. You can program a maximum of 12 favorite channels. Note: You can still use CHANNEL to cycle through all the channels you previously programmed into the TV's memory (see "Programming channels in to the TV's memory" on page 16). To program your favorite channels: 1. Tune the TV to a channel you want to program as a favorite channel. Press x or · to highlight the SET UP menu. Press y or z to highlight FAVORITE CH. SET UP CH TV CABLE VCR CHANNEL yz EXIT EXIT FAV CH TV/VIDEO A PLAY PIP FF REC TV/VCR STOP FAV CH zy STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP CT-90037 Using the TV's Features MORE TIMER: DEMO: 0 MIN START [STOP] FAVORITE CH MOVE [ ] START [ ] 5. 8. Press x or · to display the FAVORITE CH menu. Press z to add the current channel to the list. Press EXIT. SET UP FAVORITE CH [SET ] CLEAR 2 5 6 11 0 0 0 0 0 0 0 0 [TV: CYAN, CABLE: BLUE] SELECT [ ] SET [ ] 9. Repeat steps 1­8 for up to 12 channels. (Continued on next page) 18 Introduction To select your favorite channels: Press FAV CH zy on the remote control to cycle through the favorite channels you programmed. Note: The FAV CH zy buttons will not work unless you program at least one favorite channel. Tune the TV to the channel you want to clear from your favorite channel list. Press x or · to highlight the SET UP menu. Press x or · to display the FAVORITE CH menu. Press x or · to highlight CLEAR. MENU CH VOL MENU/ ENTER VOL yz x · CH TV CABLE VCR Connecting your TV EXIT FAV CH TV/VIDEO A PLAY PIP FF EXIT REC TV/VCR STOP FAV CH zy STILL SOURCE SLOW PAUSE REW PIP CH LOCATE SWAP Using the Remote Control SET UP CT-90037 FAVORITE CH SET [CLEAR] 2 5 6 0 0 0 0 0 0 0 0 0 [TV: CYAN, CABLE: BLUE] SELECT [ ] CLEAR [ ] 7. Press z to clear the current channel number from the list. Repeat steps 1­8 for other channels you want to clear from your favorite channel list. Setting up your TV Using the V-Chip Control (blocking) feature You can use the V-Chip Control feature to block certain programs or channels, to prevent others from viewing them. Selecting a PIN code Before you can block programs or channels, you must select a personal identification number (PIN) code. Your PIN code allows you to access the V-Chip Control menu, and prevents others from changing the rating and blocking limits you set. To select your PIN code and access the V-Chip Control menu: 1. [. . . ] DURING THIS PERIOD, TCL WILL, AT TCL'S OPTION, REPAIR OR REPLACE A DEFECTIVE PICTURE TUBE WITH A NEW OR REFURBISHED PICTURE TUBE WITHOUT CHARGE TO YOU, EXCEPT THAT, IF A DEFECTIVE PICTURE TUBE IS REPAIRED OR REPLACED AFTER ONE (1) YEAR FROM THE DATE OF THE ORIGINAL RETAIL PURCHASE, YOU PAY LABOR CHARGES INVOLVED IN THE REPAIR OR REPLACEMENT. Rental Units The warranty for rental units begins with the date of first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first. *Commercial Units Televisions sold and used for commercial purposes have a limited ninety (90) day warranty for all parts, labor, and picture tubes. (4) Labor service charges for set installation, setup, adjustment of customer controls, and installation or repair of antenna systems are not covered by these warranties. [. . . ]