User manual TOSHIBA 50HM66

[. . . ] HM66_EN. book Page 1 Thursday, February 23, 2006 2:49 PM Integrated High Definition DLPTM Projection Television HIGH-DEFINITION TELEVISION 50HM66 56HM66 IMPORTANT NOTE Before connecting, operating, or adjusting this product, carefully read the Important Safety, Installation, Care, and Service information in the Installation Guide. For an overview of steps for setting up your new TV, see page 4. Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider. Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLPTM TV lamp technology and is NOT a sign of malfunction. [. . . ] · If the stereo sound is noisy, select Mono to reduce the noise. 5 To save the new settings, highlight Done and press T. To reset the settings to the factory defaults, highlight Reset and press T. To listen to an alternate language on an ATSC digital station (if available): Highlight the Language field in step 3 above, and then press C or c to select the language you prefer. To listen to a second audio program on an analog station (if available): Select SAP in step 3 above. Notes: · A second audio program (SAP) can be heard only on those TV stations that offer it. For example, a station might broadcast another language as a second audio program. If you have SAP on, you will see the current program on the screen but hear the other language instead of the program's normal audio. 33 HM66 (E/F) Web 213:276 HM66_EN. book Page 34 Thursday, February 23, 2006 2:49 PM Chapter 5: Using the TV's basic features Using the StableSound® feature The StableSound® feature limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial). Selecting the optical audio output format You can use this feature to select the optical audio output format when you connect a Dolby Digital decoder or other digital audio system to the Optical Audio Out terminal on the TV (- "Connecting a digital audio system" in the Installation Guide). To turn on the StableSound® feature: 1 2 3 To select the optical audio output format: Press Y and open the Audio menu. In the StableSound field, select On. Audio Settings Bass Treble Balance StableSound Reset 100 100 0 On Done 1 2 3 Press Y and open the Audio menu. In the Optical Output Format field, select either Dolby Digital or PCM, depending on your device. Audio Setup MTS Language Speakers Optical Output Format Reset Stereo English On Dolby Digital Done 4 To save the new settings, highlight Done and press T. To revert to the factory defaults, highlight Reset and press T. Note: The RESET function returns your audio adjustments to the following factory settings: 4 To save the new settings, highlight Done and press T. To revert to the factory defaults, highlight Reset and press T. Bass . . center (50) center (50) center (0) Off To turn off the StableSound feature: Select Off in step 3 above. Turning off the built-in speakers You can use this feature to turn off the TV speakers when you connect an audio system to your TV (- "Connecting a digital audio system" and "Connecting an analog audio system" in the Installation Guide). To turn off the built-in speakers: 1 2 3 Press Y and open the Audio menu. In the Speakers field, select Off. Audio Setup MTS Language Speakers Optical Output Format Reset Stereo English Off Dolby Digital Done 4 To save the new settings, highlight Done and press T. To revert to the factory defaults, highlight Reset and press T. To turn on the built-in speakers: Select On in step 3 above. 34 HM66 (E/F) Web 213:276 HM66_EN. book Page 35 Thursday, February 23, 2006 2:49 PM Chapter 5: Using the TV's basic features Using the Locks menu The Locks menu includes the Enable Rating Blocking, Edit Rating Limits, Channels Block, Input Lock, Front (control) Panel Lock, and New PIN Code features. You can use these features after entering the correct PIN code. When the correct PIN code is entered, the Locks menu opens. Locks Enable Rating Blocking Edit Rating Limits Channels Block Input Lock Front Panel Lock New PIN Code Off Off Off Entering the PIN code 1 Press Y and highlight the Locks menu icon. Navigate ENTER Select MENU Back EXIT Exit If you cannot remember your PIN code While the PIN code entering screen is displayed, press E four times within five seconds. The PIN code will be cleared and you can enter a new PIN code. Locks Enable Rating Blocking Edit Rating Limits Channels Block Input Lock Front Panel Lock New PIN Code Off Off Off Changing your PIN code EXIT Exit Navigate ENTER Select CH RTN Back 2 Press b, which displays the PIN code entry screen. · The Lock System screen (below) appears if a PIN code has not been stored. Press the Channel Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press T. Lock System Please enter a 4 digit PIN code Confirm PIN code 1 2 3 4 Press Y and highlight the Locks menu icon. Press b to display the PIN code entering screen. Enter your four-digit PIN code and press T. Press b to highlight New PIN Code and press T. Locks Enable Rating Blocking Edit Rating Limits Channels Block Input Lock Front Panel Lock New PIN Code Off Off Off Navigate ENTER Select MENU Back EXIT Exit Cancel Done 5 6 · The Locks/Active screen (below) appears if the PIN Press the Number buttons to enter a new four-digit code. Retype the numbers to confirm the PIN code you entered. The new PIN code is now active. New PIN Code code is already stored. Use the Number buttons to enter your four-digit code and press T. Locks Active Please enter the 4 digit PIN code Please enter a 4 digit PIN code **** Confirm PIN code **** Cancel Done **** Cancel Done If the wrong PIN code is entered, the message "Incorrect PIN code, please try again!" appears. Enter the code again and press T. 35 HM66 (E/F) Web 213:276 HM66_EN. book Page 36 Thursday, February 23, 2006 2:49 PM Chapter 5: Using the TV's basic features Blocking TV programs and movies by rating (V-Chip) Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). [. . . ] 27 POWER button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 D Defaults, restore TV factory . . . . . . . . . . . . 22 Digital audio selector . . . . . . . . . . . . . . . . . . . . . . 32 Digital signal meter . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]