User manual TOSHIBA 62HM116

[. . . ] HM116_EN. book Page 1 Monday, June 19, 2006 7:30 PM Integrated High Definition DLPTM Projection Television HIGH-DEFINITION TELEVISION 62HM116 IMPORTANT NOTE Before connecting, operating, or adjusting this product, carefully read the Important Safety, Installation, Care, and Service information in the separate Installation Guide. For an overview of steps for setting up your new TV, see page 7. Note: To display a High Definition picture, the TV must be receiving a High Definition signal (such as an over-the-air High Definition TV broadcast, a High Definition digital cable program, or a High Definition digital satellite program). For details, please contact your TV antenna installer, cable provider, or satellite provider. Note: If the TV is powered off and then quickly on again when the lamp unit is hot, it may take several minutes for the picture to appear on-screen. This is a property of DLPTM TV lamp technology and is NOT a sign of malfunction. [. . . ] · If you used a hub or switch to connect the TV to your home network, you will not be able to use the automatic setup, and must manually set up the network address. · If you used a router with built-in DHCP functionality, use the automatic setup. Connecting the TV to your home network 1 2 Connect the TV to your home network via the TV's RJ-45 (Ethernet) port. See the Installation Guide for connection instructions. If you want to use file sharing only and do not have Internet service in your home: Go to section B, "Setting up the network address, " at right. Note: If you do not have Internet service, you will not be able to use the e-mail scheduling feature. Router technology, like all new and emerging technology, may from time to time cause compatibility issues because of the differences in router systems implemented by the various router manufacturers; however, most issues can be easily resolved. If you think your Toshiba TV and router might have compatibility problems, please contact the following: In the U. S. , call TACP Consumer Solutions at 1-800-631-3811 or visit http://www. tacp. com/ customersupport/contact. asp. Automatically setting up the network address 1 2 3 Press Y and open the Setup menu. Open the Network menu. If you want to use file sharing and e-mail scheduling: a) You must have Internet service in your home and a dedicated e-mail address for the TV (different from your personal e-mail address). Contact your ISP to obtain and set up Internet/e-mail service in your home. b) After you have obtained Internet/e-mail service in your home (from your ISP), go to section B, "Setting up the network address" at right. (continued) 57 HM116 (E/F) Web 213:276 HM116_EN. book Page 58 Monday, June 19, 2006 7:30 PM Chapter 7: Using the THINCTM home network feature 4 Highlight Basic Network Setup and press T. d) Retry the automatic network address setup by following these steps: (1) Highlight OK and press T. Network Basic Network Setup E-mail Scheduling Setup Home File Server Setup Software Upgrade (2) Repeat steps 1­6. (If you have already repeated this setup process, go to step 9. ) 9 CH RTN Back EXIT Exit Navigate ENTER Select 5 The message "Obtain network address automatically?" will display. Highlight Yes and press T. Basic Network Setup Obtain network address automatically? If, after repeating steps 1­6, you receive the error message shown in step 8: Either. . . a) Highlight "OK" and press T. b) Go to "Manually setting up the network address. " Or. . . a) Highlight "OK" and press T. b) Continue to sections C, D, and E (- pages 59­66) (to set up and use file sharing) and/or to sections F and G (- pages 67­75) (to set up and use e-mail scheduling). If the file sharing and/or e-mail scheduling features work correctly, then the automatic network address setup was successful (even though the TV displayed the error message). Yes No 6 The message "Please wait. . . " will display while the TV is attempting to load the network address information from the DHCP server. Basic Network Setup Please wait. . . Manually setting up the network address If the automatic network address setup is successful, go to step 7. If the automatic network address setup is not successful, go to step 8. This setup requires the data listed below. You can get this data from either your ISP or the configuration utility for your DSL/cable modem or router. ___ ___ Gateway (Router) address: ___ ___ ___ . ___ ___ DNS (Domain Name Server) address: ___ ___ ___ . [. . . ] 40 Dynamic contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 V V-Chip blocking (Locks menu) . . . . . . . . . 47 Video input label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 N Network address, setup . . . . . . . . . . . . . . . . . . 57 E E-mail account setup . . . . . . . . . . . . . . . . . . . . . . 67 E-mail recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]