User manual TOSHIBA CB-416-T3-QQ

[. . . ] TEC Color Printer CB-416-T3-QQ Owner's Manual Table of Contents We, TOSHIBA TEC Corporation of 570 Ohito Ohito-cho Tagata-Gun Shizuoka-Ken 410-2323 JAPAN, declare in our sole responsibility that this product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] This sensor is designed to locate black marks on the back of the tags by the reflection of light. Enter the amount of space between labels (label gap) or width of a black mark in Label Gap. If a proper value is not entered, the print start position will be misaligned. 3. 6. 3 Label Gap Notes: · This measurement is ignored if None is specified in Sensor. · The setting made in this section can be saved in the file as a preferred setting for a particular print job. · See A1. 3. 2 and A1. 3. 3 for gap specification. 54 Chapter 3 3. 6. 4 Issue Settings Issue mode, cut interval and print speed can be specified. Printing Note: The settings made in this section can be saved in the file as the printing preferences for a particular print job. See Section 3. 3. 4 for more detail. Note: Please select Batch Mode (with Back Feed), if the Cutter Module (option) is installed on the printer. Click the Issue Mode down arrow, and select either Batch Mode (with Back Feed) or (no Back Feed). In Cut, Disabled is selected by default. However if the Cutter Module (option) is installed on the printer, click the Cut down arrow, and select one of the following options: Note: DIP Swtich A Switch 2 must be ON to enable the cutter. See Appendix A2 for the setting of the switches. · Select After Every Label, if a cut is required after each label is printed. · Select After Entire Job, if a cut is required after the entire print job is printed. · Select Specified Interval, if a cut is required after the number of labels, specified in Interval is printed. In other words, cutting is performed every third label. The value in Interval can be changed by entering a new value. Click the Print Speed down arrow, and select either 6 inches (152. 4mm)/s or 4 inches (101. 6mm)/s. Note: When selecting 90° for the orientation of the bar font, select 4 inches/sec. 55 Chapter 3 3. 6. 5 Fine Adjustment Printing Note: The settings made in this section can be saved in the file as the printing preferences for a particular print job. See Section 3. 3. 4 for more detail. In Fine Adjustment, the following can be adjusted. First mark the Set checkbox, and the items which can be adjusted will appear. Depending on the Issue Settings, some of the items cannot be adjusted. (They are grayed out. ) Notes: · See Appendix 5 for further information. · For back feed and cut/strip fine adjustments, the Cutter Module must be installed and enabled. · In Feed, the print start position can be adjusted. · In Backfeed, the length of label stock that is fed back before printing, can be specified. Depending on the type or size of media, the print start position of ONLY the FIRST label or tag may be different from what is defined in the Feed fine adjustment. If there is a difference that is not permissible, adjust the back feed distance. This adjustment does not have any impact upon the print start position after the first label or tag. [. . . ] Clearing the Parameter Note: See A5. 7. 8 for further information about the initial values after clearing the parameters. NO RAM CLEAR When "<4> RAM CLEAR" is shown, press the PAUSE key. PARAMETER CLEAR The parameters can be cleared by pressing the PAUSE key. The printer must be turned off to exit this mode. 104 Appendix 5 System Mode A5. 6 RAM Clear (Cont. ) Notes: · See A5. 7. 9 for further information about the initial values after clearing the print distance. · To clear the print distance for a particular color, press the FEED key to select the color. [. . . ]