User manual TOSHIBA CN36Z71

[. . . ] OWNER'S MANUAL Color Television TM Serial number: TOSHIBA CORPORATION, 1999 Index CN36Z71 Reference Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. CN36Z71 Model number: Appendix Using the TV's Features Setting up your TV Using the Remote Control Connecting your TV Introduction Important Information WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Precautions Installing your TV · Place the TV on the floor or on a sturdy platform. [. . . ] The 6-picture multi-search will start. LIGHT RECALL POWER TV CABLE VCR AUX MUTE TV/VIDEO TIMER 1 2 5 8 0 TE 3 CH Connecting your TV 4 4 6 7 9 12 15 6 9 CH RTN 7 VOL To cancel the preview function: Press PREVIEW again. 100 FA VO RI ENT ST RO BE ADV/ PIP CH STROBE FAVORITE Setting up your TV Using the favorite function 1. Press FAVORITE to scan the channels programmed in the TV memory by the favorite channel function (page 21). The first window will be displayed with a moving picture. Each time you press FAVORITE, the display will change in the following order. FAVORITE CH1---- FAVORITE CH2 ---- off 2. Press y z x · to select a channel you want to see with a moving picture. Press ENTER to display the channel you have selected at step2 with a normal picture. 6 7 9 X FAV MENU/ ENTER FAV ENTER PREVIEW Using the Remote Control ADV/ PIP CH STOP SOURCE PLAY PIP REC TV/VCR REW STILL LOCATE SWAP Note: · When the main picture source is "color stream", the PREVIEW, FAVORITE and STROBE buttons are not available. · The FAVORITE button will not work until you have programmed your favorite channels. · The PREVIEW button will not work when the ANT 2 mode is selected. · If the V-CHIP feature is active and you try to scan a TV program that exceeds the rating limits you set, the " X" mark on the black window will appear. However, during the scanning period, the V-CHIP operation may not be done correctly. 12 18 33 42 97 106 Using the TV's Features To cancel the favorite function: Press FAVORITE again. Using the strobe function Press STROBE to start the strobe function. 9-picture multi-strobe starts for the present main picture. Appendix For example, you can watch a decisive moment of a sport program that has been recorded previously. To cancel the strobe function: Press STROBE again. Reference Index 26 EX FF IT PR EV W IE Using V-CHIP control Some TV programs and movies include signals that classify the content of the program (violence, sex, dialog, language). The V-CHIP control feature in this TV detects the signals and blocks the programs according to your selections. To use this feature, perform the following setup. LIGHT RECALL POWER TV CABLE VCR AUX PICTURE AUDIO SET UP PREMIUM CYCLONE PREFERENCE C. CAPTION MUTE TV/VIDEO TIMER RECALL START V­CH I P PUSH START CH L ABEL PUSH FAVOR I TE CH1 START PUSH FAVOR I TE CH2 START PUSH START RESET PUSH 1 4 7 2 5 8 0 TE 3 CH 6 CH RTN To end push EXIT VOL 3. Press x or · to display the pin code entering mode. · Factory reset status : Set your 4 digit code by pressing the Number buttons (0-9). · When the pin code is already stored : Press the Number buttons (0-9) to enter the 4-digit pin code used to block channels. PICTURE AUDIO SET UP PREMIUM CYCLONE PREFERENCE C. CAPTION 100 FA VO RI ENT ST RO BE ADV/ PIP CH MENU/ENTER FAV MENU/ ENTER FAV yzx · EX IT ADV/ PIP CH PICTURE AUDIO SET UP PREMIUM CYCLONE PREFERENCE C. CAPTION STOP SOURCE PLAY PIP V­CH I P BLOCK I NG RESET P I N CODE 1110 V­CH I P BLOCK I NG ACT I VE P I N CODE 1234 REC TV/VCR REW FF STILL LOCATE SWAP To enter push 0-9 To set push ENTER To end push EXIT To enter push 0-9 To set push ENTER To end push EXIT If a wrong pin code has been entered, the message "Incorrect" will appear. If you can not remember the pin code you have stored, while in the pin code entering mode, press the RECALL button four times within 5 seconds. The pin code you have stored will be released. Press ENTER to display the V-CHIP menu. PICTURE AUDIO SET UP PREMIUM CYCLONE PREFERENCE C. CAPTION PUSH PUSH START To end push EXIT Continue to set each item following the steps on the next page. 27 Reference Index Appendix V­CH I P ENABLE BLOCK I NG SET RAT I NG BLOCK I NG OPT I ON NEW P I N CODE BLOCK CHANNEL On START PUSH PUSH Off START START Using the TV's Features Setting up your TV Using the Remote Control 9 Number Connecting your TV Selecting the V-CHIP menu 1. Press MENU, then press x or · until the SET UP menu appears. Press y or z to highlight V-CHIP. Introduction PR EV IE W Introduction Adjusting the V-CHIP menu ENABLE BLOCKING Press x or · to select On or Off. [. . . ] 24 video input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Using the Remote Control X XDS information, displaying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 S SAP, selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 satellite receiver/DVD and a VCR, connecting . . . . . . . . . [. . . ]