User manual TOSHIBA D-R150

[. . . ] Introduction DIGITAL VIDEO DVD VIDEO RECORDER D-R150SB OWNER'S MANUAL Connections INSTALLATION GUIDE Read this booklet first. Basic Setup H PM002XXXX010 © 2005 Toshiba Corporation 01_D-R150SB(E)_inst 1 05. 7. 13, 0:23 AM Introduction SAFETY PRECAUTIONS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. This DVD video recorder employs a Laser System. [. . . ] To switch the output signal (Progressive/Interlaced) PROGRESSIVE Press PROGRESSIVE on the remote control. The output signal alternates between component progressive and component interlaced. · When "PSO" is displayed on the front panel display, the output signal is progressive. When "PSO" is not displayed, the output signal is interlace. · The following setting is required according to the TV that you are connecting. Perform this setting after step page 15). 4( "Audio out select" on the Setting "AV1 output" on the "Initial settings" menu. "Picture/Audio settings" menu. page 38 page 40 Basic Setup TV TV or monitor equipped with component video inputs "Video" or "S-Video" "Analog 2ch" · Selecting "RGB" disables signal output from the COMPONENT OUT (Y, PB, PR) jacks. If the on-screen display disappears immediately after you select "RGB", you can restore it by connecting the recorder using the AV OUT VIDEO (yellow) jack. · If you display the setup menu when the output signal is progressive, it automatically changes to interlace. Press PROGRESSIVE again after you exit the menu. Notes · Refer to the owner's manual of the connected TV as well. · When you connect the recorder to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before any connections. · If you place the recorder near a tuner or radio, the radio broadcast sound might be distorted. In this event, place the recorder away from the tuner and radio. · The output sound of the recorder has a wide dynamic range. Be sure to adjust the amplifier's volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound. · Turn off the amplifier before you connect or disconnect the recorder's power cord. If you leave the amplifier power on, the speakers may be damaged. · Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 625 progressive scan picture problems, it is recommended that the user switch the connection to the "Standard Definition" output. If there are questions regarding our TV set compatibility with this model 625p DVD player, please contact our Customer Service Center. 17 03_D-R150SB(E)_inst_13-20 17 05. 7. 13, 0:23 AM Connections Connecting a satellite receiver You can connect a satellite receiver to this recorder to enjoy watching or recording satellite programmes through the recorder. By using SCART cable If both your TV and satellite receiver have a SCART input, use a SCART cable to connect the recorder. SCART cable (not supplied) VHF/UHF aerial Satellite receiver To AV2(EXT) To AV1(TV) SCART cable (not supplied) To SCART input To aerial input TV Notes · To watch broadcast programmes by using the satellite receiver, use INPUT SEL. button on the remote control and select "AV2" (this is shown on the display on the recorder). [. . . ] · When a DVD video disc has a particular available picture shape, the contents may not be compatible with other picture shape. "C: TV shape setting" is complete. Go to "D: Remote control settings". ( page 44) 43 06_D-R150SB(E)_inst_40-48 43 05. 7. 13, 0:23 AM Basic Setup D: Remote control settings Perform this step according to your preference and usage. Operating a TV with the remote control of this recorder The remote control of this recorder has a function to operate a TV. Preparation: Entering a brand code into the remote control 1 4 7 +10 TIME SLIP DVD 2 5 8 0 TV 3 6 9 CLEAR 1 1 4 7 While holding QUICK, press the number buttons to enter a corresponding brand code (see the next page) of your TV. e. g. To enter 0071 QUICK 0 0 7 1 QUICK INPUT SEL. Hold down. PROGRESSIVE 2 5 8 0 3 6 9 TV VOL T. SEARCH TOP MENU SKIP REV STOP REV CH MENU SKIP FWD PLAY FWD ADJUST PA US E EA SY 2 Release QUICK. The brand code is memorized. VI NA INSTANT REPLAY Start ENTER INSTANT SKIP CHP DIVIDE SUBTITLE QUICK DISPLAY Operating the remote control Point the remote control into which you have entered the brand code, to your TV, and first press TV button then press the following buttons. OPEN/CLOSE ON/STANDBY ON/STANDBY : To turn on and off the TV INPUT SEL. [. . . ]