User manual TOSHIBA DR-20

[. . . ] E7TE0BD_EN. book Page 1 Friday, March 5, 2010 5:08 PM Introduction Connections DVD VIDEO RECORDER DR20KB OWNER'S MANUAL Basic Setup / TV View Operation Recording Playback Editing Function Setup Others © 2010 Toshiba Corporation EN For Customer Use: Carefully read the Model No. located at the back of the unit and enter the information below. Retain this information for future reference. __________________________ 1 E7TE0BD_EN. book Page 2 Friday, March 5, 2010 5:08 PM . Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] 3) Press [STOP C]. Note · The unit does not send out the output signal to DVC. · For the proper operation, connect DVC to the unit directly. Do not connect this unit and DVC via any other unit. · Do not connect more than one DVC. Other DV device such as cable/satellite box or D-VHS recorder cannot be recognised. · If no video signal is detected from the DVC during DVC to DVD dubbing, the recording will be paused and "I" will flash on the TV screen. The recording will resume when the unit detects the video signal again. · When the DVC is in camera mode, refer to "Guide to DV and On-Screen Display" on page 38. · Date / time and cassette memory data will not be recorded. · Pictures with a copy-guard signal cannot be recorded. · A DV terminal is a terminal that can use the transmission mode conforming to the IEEE 1394 standards called "Fire Wire". It serves as the interface that connects the PC and peripheral device such as "i. LINK" (registered trademark of SONY). It enables digital dubbing between DV devices with little degradation. Playback DVD-RW DVD-RW DVD-R DVD+RW DVD+R Before recording from DVC, see page 18 for connection instructions. Preparing for DV dubbing (DVC to DVD): · Insert a recordable DVD. · Make sure your DVC is in video mode. Editing 1 Press [INPUT SELECT F] repeatedly to select the external input channel, then press [PROG. G \ H] repeatedly to select DV(AV4). Function Setup DV AB-1234 0:00:00 2 3 Press [REC MODE] to select a recording mode. (See page 27. ) Press [DISPLAY]. Others EN 39 E7TE0BD_EN. book Page 40 Friday, March 5, 2010 5:08 PM Setting a Disc to Protect VR To cancel finalising (DVD-RW disc only): At step 4, press [STOP C]. Select "Yes" using [K \ L], then press [ENTER\OK]. Finalising is cancelled and the unit switches to stop mode. DVD-RW DVD+RW DVD+R To prevent accidental over-recording, editing or erasing of recordings, you can protect them using "Setup" menu. Insert a recordable disc. 1 In stop mode, press [SETUP]. Do you want to cancel?Yes No 2 3 4 5 Select "DVD Menu" using [K \ L], then press [ENTER\OK]. Select "Disc Protect OFF A ON" using [K \ L], then press [ENTER\OK]. Select "Yes" using [K \ L], then press [ENTER\OK]. The disc is protected. Finalising 10% If " " appears when [STOP C] is pressed, you cannot cancel finalising because the finalising has already reached at a critical point in its process. [. . . ] (The maximum is 99) Recording Error You cannot record more than 999 chapters on one disc. (The maximum is 999) Recording Error You cannot record more than 49 titles on one disc. (The maximum is 49) · Insert a ver. 1. 2 DVD-RW disc (compatible with CPRM. ) · Remove the disc protect setting in "DVD Menu" menu. [. . . ]