User manual TOSHIBA FT1000

[. . . ] Do not use this product near water sources, such as bath tubs, wash bowls, kitchen sinks, laundry tubs, wet basements, or swimming pools. Do not place this product on an unstable cart, stand, or table. The telephone may fall, causing serious damage to the telephone. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to protect the phone from overheating. [. . . ] e Place the battery pack in the battery compartment. r Put the battery compartment cover back by sliding until it snaps into place. Make sure not to get the wires of the battery pack caught in the cover. If the IN USE/CHARGE LED does not light, make sure the AC adaptor is plugged in securely and that the electrical outlet is working and not controlled by a light switch. It is important to charge the battery for 12 to 16 hours continuously without any interruption before you use the handset for the first time. 90 0M Hz Charging contacts IN USE/ CHARGE LED Note The battery pack is not charged properly if the charging contacts are dirty or tarnished. Clean the contacts occasionally with a dry cloth. 6 After the battery pack is fully charged; Operation While in use (Talk mode) While not in use (Standby mode) Approx. battery life up to 7 hours up to 7 days When TALK/BATT LOW LED blinks, all handset buttons are disabled and the battery needs to be charged. If this occurs during a call, you hear short beeps. Finish the call as soon as possible and place the handset on the base unit. Note If a call comes in when the battery is too low to operate properly, you will be unable to answer the call or the call will be disconnected. WALL MOUNTING MOUNTING ON A STANDARD WALL PLATE Insert the bracket's tab into the base's lower tab slots, then press down on the top of the bracket to snap it into the clip slots. Raise the antenna. Flip the switch hook tab over so the tab holds the handset. Telephone Line Cord Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120V, 60Hz) AC Adaptor 7 · Route the cords through the guides. · Place the base unit on the posts of the wall plate and push down until it is firmly seated. u Record the telephone numbers on the SPEED DIAL INDEX CARD, and place it on the back of the handset. EXAMPLE: To store 9012345 in memory address 3 MEM WX 9 0 1 2 3 4 5 MEM 3 Replacing a telephone number Just store the new number following the same steps in "1. STORING NUMBERS. " The new number will replace the previously stored one. 13 2. DIALING A STORED NUMBER q Pick up the handset and press TALK . w Press MEM . e Enter the memory address (0 to 9). The stored number will be dialed. Note If you enter a memory address which does not have any stored number, error beeps sound. 3. INSERTING A PAUSE IN MEMORY Use RDL/P (redial/pause) to make an outgoing call through a PBX or long distance. Each time you press RDL/P , a pause of about two seconds is inserted during the dialing sequence. If more than two seconds are needed, press RDL/P twice. EXAMPLE: To store "0 PAUSE 1234567890" in memory address 4, press: MEM 0 RDL/P 1 2 3 4 5 6 7 8 WX 9 0 MEM 4 4. CHAIN DIALING Combining ordinary dialing and memory dialing, you can dial a long telephone number with less steps. [. . . ] Or to set the dial mode for tone dialing press TONE/ Note: For long distance calls, you need a prefix "1" and the area code. Press L. D. /1 and LOCAL/3 to add "1" and the area code before press . A confirmatin tone sounds to indicate the setting is complete. Dial Mode:Pulse Tone - Press Pulse- Press # Dial Mode:Tone Tone - Press Pulse- Press # # Storing Caller ID Data to Speed Dial Memory 1 2 4 Press CID , then press Speed dial memory. Press MEM , then press or , to display the number you want to store into or enter a memory location number. Fasten the AC adaptor cord. Telephone Line Code Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120V, 60Hz) TONE/ Tone Dialing Pulse Dialing Press SELECT . A confirmation beep sounds and the Caller ID data is stored. [. . . ]