User manual TOSHIBA FT7305

[. . . ] This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take necessary measures to correct the interference. Battery Recycling Statement The following statement applies if you purchased backup batteries with your system. The product you have purchased contains rechargeable batteries. [. . . ] To assign a DBS Feature Code to a One-Touch key: 1. · The phone issues intercom dial tone. Press the One-Touch key to be programmed. To assign an Outside Telephone Number to a One-Touch key: 1. · The phone issues intercom dial tone. Press the One-Touch key to be programmed. Press CONF followed by the Pooled Trunk Access code (9, 81-86). If a pause is required, press the REDIAL key. This inserts a pause between the access code and the telephone number. 4-76 DBS Manual - Revised April 2000 DBS-2. 3/9. 2-700 Section 700 - Operation Chapter 4. · The phone issues intercom dial tone. The programmed data appears on the display. If the password is over 3 digits long, it must be assigned to a personal or system speed dial number. If you are accessing the Panasonic Voice Mail, it is best to include a # sign at the end of the password. To use a Voice Mail key: When the VM key flashes, the user presses it to connect to the mailbox. Related Programming · FF5 (Keys): FF Key Assignment for Extensions · FF5 (Keys): FF Key Assignments for DSS Consoles DBS-2. 3/9. 2-700 DBS Manual - Revised April 2000 4-79 Chapter 4. Key Telephone Features Section 700 - Operation Considerations · The VM key can be used with the Panasonic Voice Mail or with thirdparty voice mail systems. · If the voice mail password is over three digits long, assign the password to a personal or system speed dial number (00-99, 000-199 or 900-909). When you use a speed dial number with the Panasonic Voice Mail, include the pound (#) sign after the password. Excluding the # sign results in a 6second delay before you are connected to the mailbox. If you are using 2-digit dialing with a third-party voice mail, the password can be up to 4 digits long before it must be stored as a speed dial number. (Panasonic Voice Mail requires 3-digit dialing. ) · With Panasonic Voice Mail, most attendants use port group scheduling that accesses a menu, which asks for a mailbox number. Port group scheduling is used so attendants can quickly dial the mailbox numbers of other users. To assign a personal VM key for an attendant using port group scheduling, use a speed dial number to store the voice mail extension number followed by an asterisk (*), followed by the password. [. . . ] · ISDN International Code Deduct 0 1 1 Set to (1) to deduct 0 1 1 from the CO Setup message. · ISDN Long Distance 1 Code Deduction · Set to (1) to deduct 1 from the CO Setup message. Page I-16 DBS Manual - Revised April 2000 DBS-2. 3/9. 2-700 Lucent (AT&T) 5ESS · CO Type (1) 5ESS - ISDN International Code Deduct 0 1 1 - Set to (1) to deduct 0 1 1 from the CO Setup message. Nortel (NT) DMS100 CO Type (3) DMS100 (This is the default setting. ) The ISDN PRI provides a flexible method of providing access to the Public Switched Telephone Network (PSTN). Because of the many ways that the CO can configure an ISDN span, it is essential that the DBS configuration and the provisioning of the CO are compatible. The following tables identify the critical parameters that must be set for proper operation. These tables also provide a list of information that must be gathered on the CO, as well as the type of information that the CO needs to know about the DBS system. [. . . ]