User manual TOSHIBA FT8258BK

[. . . ] This manual is designed to familiarize you with the i 5803 Accessory Handset setup, registration and basic functions. For detailed operational instructions, please refer to the i 5853, i 5857, i 5866 OR i 5867 User's Manual. 1 Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. [. . . ] After the beep, and with the Handset microphone facing the audio source, start recording. NOTE: If the memory is full, the Handset will prompt Clip memory full!· · Hit the STOP softkey to stop the recording. After recording, you may PLAY or SAVE the melody. If you choose SAVE, you will be prompted to Enter Clip Name. Enter a name (up to 8 characters) for the recording. If you make a mistake, press the softkey to backspace. The melody will be stored in the My Clips section. You can listen to all of your recorded musical ringers in My Clips. If you want, when in My Clips, you can press DELETE then YES to erase any of them. Note: When you want to use the Handset microphone to record ringers, do not insert the Audio Patch Cord into the headset jack. 19 Basic Operation NOTE: Your i 5803 Handset is preset with many musical ringer options (i. e. Jazz, R&B, Reggae, Rock, etc. ) for you to use as your default ringer or a distinctive ringer. Three of them are protected, you can't replace them. You can replace the other 6 preset ringers with your own. The ringing Handset can pick up the transferred call just like any incoming call. Announced Transfer: To perform an announced transfer (call and advise another extension): · Press HOLD to place your call on hold. · Press any NavKey then the left NavKey to select Intercom, press the middle Navkey in again to confirm. -ORPress any NavKey then press the 1 key. · Press the up or down NavKey to the desired location. · Press the middle NavKey to confirm. · When the ringing Handset answers, announce that there's an active call on hold. · Press ON (on the destination Handset) to pick up the call on hold. 22 Headset Operation Your i 5803 Handset is equipped with a 2. 5mm Headset Jack for use with an optional accessory Headset for handsfree operation. If you choose to use the Headset option, you must obtain an optional accessory Headset that is compatible with the i 5803. For best results, use a VTech 2. 5mm headset. To purchase a Headset, call VTech Customer Service at 1-800-595-9511. Once you have a compatible 2. 5mm Headset, locate the Headset Jack on the i 5803 Handset. [. . . ] Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority or electrician as appropriate. Your Cordless Phone is designed to operate at the maximum power allowed by the FCC and IC. This means your Handset and Base Unit can communicate only over a certain distance - which will depend on the location of the Base Unit and Handset, weather, and the construction and layout of your home or office. 32 Technical Specifications FREQUENCY CONTROL Crystal controlled PLL synthesizer WEIGHT Handset: Charger: 164 grams (excluding battery cells) 207 grams TRANSMIT FREQUENCY Base: 5725-5850 MHz Handset: 2400-2483. 5 MHz POWER REQUIREMENTS Handset: 2 cell AA 1. 2V 1400mAh NiMH Battery RECEIVE FREQUENCY Base: 2400-2483. 5 MHz Handset: 5725-5850 MHz Charger: 6V DC @300mA CHANNELS 95 Channels MEMORY Phone Book: 50 Memory locations; up to 32 digits, 16 characters per location CID: 50 Memory locations NOMINAL EFFECTIVE RANGE Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. SIZE Handset: Charger: 197mm x 53mm x 40mm (including antenna) 85. 0mm x 85. 0mm x 86. 5mm SPECIFICATIONS ARE TYPICAL AND MAY CHANGE WITHOUT NOTICE. 33 TOSHIBA TELECOMMUNICATIONS LTD. [. . . ]