User manual TOSHIBA FT8808BK

[. . . ] This apparatus has been approved for the use of the following facilities: 1) Storage of telephone numbers for retrieval by a predetermined code 2) Last number redial 3) Simple telephone facility 4) PBX earth register recall PBX timed break register recall 5) MF signalling 6) LD signalling 7) Pause 8) 1 way paging 9) Call prohibition 10) Call restriction 11) Direct call 12) Intercom between handsets 13) Transferring a call from one handset to another 14) Conference 15) Setting the call waiting tone 16) Accessing the base unit Ringer Equivalence Number (REN): This relates to the performance of the apparatus when used in combination with other items of apparatus. It enables the calculation of the maximum number of items of apparatus that may be connected simultaneously to the line by summing the REN values of each item. A BT supplied instrument has a REN value of 1 unless otherwise marked. A maximum REN value of 4 should not be exceeded. [. . . ] 2 ·Presscurrent handset ringer pattern is displayed The 23 I Ex. 4 is selected. 3 Press a button pattern. 1 to 6 to select the ringer · The selected ringer pattern is displayed and rings. 23 4 4 ·When finished, presssounds. (Program). A confirmation tone Setting the Key Tones You can select whether the handset keys sound tones or not (key tone, confirmation tone, error tone). The factory preset is 1 (ON). Chapter 3 Advanced Operations 1 Press (Program). 2 , then 1 2 ·Presscurrent setting. The To 3 ORselect OFF, press 0. 2i i Ex. OFF is selected. To select ON, press 1 . 4 ·When finished, pressconfirmation tone sounds. If ON is selected, a 2i 0 43 Setting the Range Warning Alarm You can select whether the handset sounds a range warning alarm or not. The factory preset is 0 (OFF). 1 Press (Program). 2 Press 2 , then 5. 25 0 Ex. ON is selected. 3 To select ON, press 1 . · A confirmation tone 25 i Setting the Battery Low Alarm You can select whether the handset sounds a battery low alarm or not. If it is not registered within 1 minute, press (Program) on the handset to cancel the programming mode. Then start from step 1 again. 1 Base unit: hold Press and (Page) for more than 10 seconds until the in use indicator ( ) lights. In Use Indicator ( Page Button ) 2 Handset: Press ·" (Program). " is displayed. 7 1. 3 ·Pressbase, then numbers where the handset The unit has not been registered are displayed. 7 i i234 48 4 Press the1desired . base unit number using buttons to 4 · " " flashes. · While the handset is searching for the base unit, "­" flashes across the display. · The number is assigned as the base unit number for the handset. Ex. Base unit 1 is assigned. - Multi-Unit User Operations 5 Enter the base unit password using a 4 digit number. · The factory preset of the base unit password is 0000. If you have changed the base unit password (p. 35), enter the new password. 7i 7 i ---Ex. The handset is registered in base unit 1 . 6 ·When finished, presssounds. (Program). A confirmation tone · " " stops flashing. ·" " goes out and the handset is registered in the base unit. [. . . ] It contains toxic heavy metal Hydride and therefore should be recycled. 77 Useful Information Chapter 5 Dear purchaser, You have acquired a FT8808BKE-B, which is a product made in regard with the European Standards for Cordless Telephones (DECT). DECT technology is characterised by high-security protection against interception as well as high-quality digital transmission. This telephone was designed for a wide range of applications. For example, this telephone can be used within a network of base units and handsets, constituting a telephone system which: · operates up to 6 handsets from one base unit · allows intercom between 2 handsets · allows a handset to operate from 4 base units, expanding the communication radio area. [. . . ]