User manual TOSHIBA FT8958BK

[. . . ] Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool). Do not place this product on an unstable surface. The product may fall, causing serious damage. Slots and openings in the Handset and Base Unit are provided for ventilation. [. . . ] When the system announces the correct minute, press TIME/SET. The system announces the current clock setting. NOTE: Press any PLAY/STOP button to exit programming at any time. The PLAY/STOP buttons are located on the Base Unit and are labled numbers 1, 2, and 3. These buttons also playback messages left in their respective mailbox. 23 Answering System Operation Press ON/OFF to turn the system on or off. When the system is turned on, you will hear "Answering machine on" and the ON/OFF light will be lit. When the system is off, you will hear "Answering machine off" and the ON/OFF light will not be lit. The system will still answer after 10 rings if it is off, then announce "Please enter your security code" and wait for you to enter your two-digit code to access remote functions. (See Remote Access on page 31 for details. ) Answering System Operation About Mailboxes This answering system has three voice mailboxes. Callers using a touch tone phone can select the mailbox in which their messages will be recorded by pressing 1, 2, or 3 while the system plays the outgoing announcement. Otherwise, messages will be recorded in Mailbox 1. About Announcements · · You can record two different announcements - one for normal answering and one for when you've set the system to play the announcement only. Press CHANGE until you hear your desired setting. Press TIME/SET to confirm your selection. 25 Answering System Operation Answering System Operation FEATURE SUMMARY SYSTEM ANNOUNCES: "Set Security Code" 50* (Default setting indicated by "*") DESCRIPTION/DIRECTIONS: Set the remote access code you will use to access features and functions of the answering system from a touch tone phone. Choose a two-digit number from 40 to 99. When Message Alert is turned on the Base beeps once every 10 seconds when new messages have been received. When you turn Announce Only on, callers hear your announcement but cannot leave a message. Turn the Base ringer on or off. "Set Audible Message Alert" Off* On "Set Announce Only" Off* On "Set Base Ringer" On* Off "Set Number of Rings" 2 4* 6 Toll Saver Answering System Operation Choose how many times the phone will ring before the system answers a call. With Toll Saver active, the system answers after two rings when you have new messages and after four rings when you have no new messages. NOTE: Exit Feature Setup at any time by pressing any PLAY/STOP button. 26 Answering System Operation This system automatically saves your messages until you delete them, and can store approximately 15 minutes of messages, memos and announcements (up to a maximum of 99 messages). A message or memo can be up to 4 minutes long. If the system has less than 30 seconds of recording time left, it automatically turns off. The system will still answer after 10 rings, announce "Memory full, please enter your security code" and wait for the caller to enter the code to access remote functions. (See Remote Access beginning on page 31 for details. ) When you have new messages or memos, the PLAY/STOP light for each mailbox with new messages will flash. Listen to Messages Before each message or memo plays, the system announces the day and time it was received. [. . . ] · Programming/testing of emergency numbers should be performed during off-peak hours, such as in the early morning or late evening, when the emergency services tend to be less busy. IC (Industry Canada) This telephone is registered for use in Canada. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. 41 Additional Information FCC, ACTA and IC Regulations Notice: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. [. . . ]