User manual TOSHIBA FT9003BK

[. . . ] · Significant obstacles such as concrete walls or metallic supports (windows and door frames, partitions, etc. ) will lessen the communication range between the base station and the handset. Installing the charger on a horizontal surface 1 Plug the power cable into the charger. 2 3 Plug the power cable into the wall socket. Place the handset in the charger. Installing your extra handset 7 Mounting the charger on a wall 1 Fix the screws (not supplied) according to the diagram below. 3 mm 2 - 2. 5 mm 46 mm 1. 5 - 2 mm 8 mm 2 3 4 5 Plug the power cable into the charger as shown on page 7. Plug the power cable into the wall socket. Place the handset in the charger. 8 Installing your extra handset Charging your handset Your handset is powered by 2 rechargeable AA/R6 batteries. Before you use your handset for the first time, charge it for at least 16 hours. [. . . ] After a few seconds, the handset beeps and REGISTER is displayed. If the handset cannot find a base station, FAILED will be displayed, and you will need to try again. Press 6 R to leave menu mode. 10 Installing your extra handset Changing the name of your base station The default name of your base station is "TOSHIBA". You can change this name from your extra handset as follows: 1 2 Press o. o. R, then press + to display SETUP. Press Press - until BASE NAME is displayed, then press If the base station has a name, this will be displayed. You can delete the existing name using the + key. If the base station has no name, BASE NAME?You can enter characters by pressing the key with the required character on it one or more times. These characters are engraved on the handset keypad. If you wish to enter two successive characters which are on the same key, you need to distinguish them by pressing the - key between the two characters. For example: to enter TOSHIBA you would press the following keys. To hang up, press t or replace the handset in the charger. 2 3 If you press * to call all handsets, and one of your handsets is in Baby Sit mode, then this handset will take the call. Note: Using your extra handset 13 Answering an internal call When another handset calls you, your handset will ring with the internal call melody, the t symbol will blink on the display and the number of the handset calling you will be displayed. To hang up, press charger. 2 t or replace the handset in the Using the handset loudspeaker Your extra handset is fitted with a loudspeaker as well, so that other people with you can listen to the conversation. The sound is amplified through the loudspeaker at the back of the handset. Adjust the volume of the loudspeaker when it is on, using + or -. To turn off the loudspeaker, press 2 3 H again. Managing the Baby Sit mode The Baby Sit mode allows you to monitor sounds coming from another room (e. g. Because the Baby Sit mode is a special type of inside call, it requires two handsets (of type Onis 6810 or 6816): one left in the baby's room (Baby Sit mode handset) and one you keep with you (Parents handset). In order to use the Baby Sit mode, you must first set the handset to be left in the room to be monitored (e. g. the baby's room) in Baby Sit mode. Setting a handset in Baby Sit mode 1 Press R, then press displayed. . - until BABY SIT is 2 3 Press + or - to select ON. Your handset beeps to indicate that the setting has been changed. Press R to exit menu mode. . 14 Using your extra handset Note: The handset in Baby Sit mode will not ring but can be used to make and receive calls. [. . . ] Once the other handset answers, you can either : - initiate the conference call by pressing o. - switch back and forth between the other handset and your outside call by using e. If the other handset does not reply, you can return to your outside call by pressing e, or you can hang up by pressing t . To prevent unwanted key presses, you may want to lock the handset keypad. [. . . ]