User manual TOSHIBA IK-64DNA

[. . . ] 1-2 1-2 1-2 1-3 1-4 1-4 1-4 1-5 1-5 1-5 1-5 1-6 1-6 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 (IK-64DNA) IMPORTANT SAFEGUARDS 1. Read Instructions All the safety and operating instructions should be read before the product is operated. [. . . ] Overloading Do not overload power supply and extension cords as this can result in a risk of fire or electric shock. Object and Liquid Entry Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of kind on the video product. Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requiring service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions. when the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the video product. If the video product has been exposed to rain or water. If the video product does not operate normally by following the operating instructions in the instruction manual. Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. DC : When using Al lens (without amp). LEVEL : DC - Type AI Lens adjustment trimmer Rear View Video output terminal : connect to a TV monitor, etc. AC 24V ~ / DC 12V --power terminal VIDEO OUT DC 12V--- DAY/NIGHT LEVEL DAY/NIGHT (ON/OFF) Right Side View Focus Lock Screw Left side View Top View ON OFF LINE LOCK BLC 12 3 4 Recorder Ready V PHASE : Line-Lock Phase adjustment trimmer LEVEL H L AES VIDEO DC IRIS V PHASE AC 24V ~ GND 2. COMPONENTS : (1) Camera (2) Accessories (a) Lens Connector (b) Instruction Manual (c) Lens Cap 1 1 1 (E4-191J-100(M)) 1 Auto -IRIS Terminal When using an auto -iris it needs to be connected to this terminal. Focus ring : Rotate the ring to appropriate setting. Select switch : Line Lock mode ON/OFF BLC ON/OFF Day / Night ON/OFF Day / night Level Selection Lens : Mount a CS-mount lens. Front View 63 116 50 1-2 Recorder Ready 4. CONNECTIONS AND OPERATIONS Notes on connecting Power plugs of connected equipment must be disconnected before installations. A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection. For details of wiring and operation of equipment to be connected, refer to their operation manuals. Lenses, coaxial cables for video signals and the power cord are not supplied with the camera. Line - Lock control Matching the vertical synchronization with the power frequency is called the Line-Lock. This function is activated when the LINE LOCK switch is set to ON. ON OFF LINE LOCK O N 1 2 3 4 1. Basic connection Single system configuration MONITOR TV When two or more cameras are switched by the video switcher for viewing by a monitor TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching. CAMERA1 MONITOR TV Recorder Ready CAMERA2 VIDEO SWITCHER TO 24V AC UL Listed Class 2 power supply 1-3 CAMERA VIDEO OUT DC 12V . . . Recorder Ready LEVEL H L AES VIDEO DC V PHASE AC 24V ~ GND AC 120V ( ) POWER CORD (twisted pair line) minimum wire size of 18 AWG is recommended. 24V AC UL Listed Class 2 power supply / 12V DC power supply CAUTION : Never input 24V AC and 12V DC at the same time. Cautions : The camera is synchronized to the power frequency of 60 1 Hz covering a normal fluctuation of the power frequency. However, the camera may not cover a large fluctuation caused from the power generated by an engine generator, etc. [. . . ] This function is effective when a strong light enters the portion other than this zone and auto iris lens closes and darkens the area to view. Video IRIS Lens 1. NC VIDEO GND VIDEO position Direct Drive IRIS Lens 1. Driver _ (g) DC position (Monitor screen) 3 4 1 2 60% 60% 8. WHITE BALANCE (AWB) In this camera, the white balance is automatically adjusted corresponding to the color temperature variations on the object. [. . . ]