User manual TOSHIBA IK-65WDA

[. . . ] INSTRUCTION MANUAL CCD COLOR CAMERA IK-65WDA Please read this manual thoroughly before use, and keep it handy for future reference. Record in space provided below the Model No. ____________ Retain this information for future reference. TABLE OF CONTENTS Important Safeguards 1. Features & Description ······································································· 4 2. Cautions ······························································································4 3. [. . . ] Press and hold the select switch on the side of the camera body 2 seconds until the menu appears on the monitor. The shaded area represents the option to be set. (Displayed when both DIP3 and DIP4 on the rear are not set to ON). Displays the present state of the rear switches. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T (1) WDR = Wide dynamic range function Displays the rear switch status of the switch (DIP 3). (2) D/N = DAY/NIGHT function Displays the rear switch status of the switch (DIP 4). (3) ALC = Automatic level control Move the cursor to the position shown in fig. Use the L M SELECT switches to adjust the ALC level to reach the desired luminosity. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T 13 (4) BLC = Back light compensation Move the cursor to the position in Fig. Use the SELECT switches to select OFF, AUTO, UPPER2/3, LOWER2/3, CENTER1/ 3, CENTER1/6, LOWER1/6 Using in AES or auto iris lens, the exposure adjustment is automatically controlled so that the best picture is obtained at next monitor zone. This function is effective when strong light enters and auto iris lens closes. OFF:The camera is not in BLC mode. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T The area size is approximately the following: (Appropriately maintain the shaded area of the video level) 1 OFF 2 UPPER 2/3 2 3V 1 3V 3 LOWER 2/3 1 3V 2 3V 4 CENTER 1/3 1 3V 1 3V 1 3V 1 3H 1 3H 1 3H 5 CENTER 1/6 1 3V 1 3V 1 3V 1 4H 1 2H 1 4H 6 SIDE 1/6 1 3V 1 3V 1 3V 1 4H 1 2H 1 4H 7 AUTO Depending on the subject conditions, areas 1 to 6 can be combined. NOTE · The camera automatically decides which areas are dark in AUTO mode, and the brightness for these areas are adjusted to their optimum levels. Consequently, the bright parts of the image may be affected may be affected. 14 (5) GAIN = AGC gain setting Move the cursor to the position in Fig. Use the SELECT switches to select OFF, STD, HIGH. STD : Standard position, max gain = 24dB HIGH : High-Sensitivity position, max gain = 30dB (If there is noise in low light conditions, set to STD. ) WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T NOTE · If the SHUTTER settings are set to S. D/N (excluding X1), then OFF cannot be set. (6) ID. = Camera ID. Move the cursor to the position shown in fig. Use the SELECT switches to name each camera up to 20 characters. Font list 0, 1, 2, 3, 4, 5, 6, 7, 8, 9 A, B, C, D, E, F, G, H, I , J, K, L, M N, O, P, Q, R, S, T, U, V, W, X, Y, Z . + -- / &<> ( ) · (SPACE) x WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. I D - POS OF F DIP DIP 00 SW SW . . . . . . EX I T CANCE L DE F AUL T (7) ID. Position Move the cursor to the position shown in fig. Use the SELECT switches to select OFF, TOP, BOTTOM. OFF TOP : The camera ID is not displayed : The camera ID is displayed at the top-left of the monitor BOTTOM : The camera ID is displayed at the bottom-left of the monitor. WD R * * * - C HG D / N * * * * * - C HG ALC LEV : BLC AUTO GA I N S TD ID. [. . . ] Press and hold the switch on the side of the camera body 2 seconds until the menu appears on the monitor. The blinking area represents the option to be set. (This sub menu cannot control from a keyboard by RS-422) Default settings ADDRE S S P ROTOCOL B I T - RAT E 001 TO S H I BA - P 4800 (1) ADDRESS Move the cursor to the position in Fig. Use the SELECT switches to select 001 to 255. [. . . ]