User manual TOSHIBA IK-TF5U

[. . . ] INSTRUCTION MANUAL CAMERA CONTROL UNIT IK-TF5U For Customer Use Enter below the Serial # which is located on the bottom of the cabinet. Retain this information for future reference. Model #: Serial #: IK-TF5U FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] (Refer to the item "7. 2 (3) WHT BAL (white balance)". ) · Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor etc. (Refer to the item "7. 2 (3) (3. 2) Changing each setting in MANU (Manual) mode". ) 9 5. 3 Gain When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level. For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. (Refer to the item "7. 2 (2) GAIN (Video gain)". ) 1 MANU (Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps. (Refer to the item "7. 2 (2) (2. 1) (a) Changing the gain in MANU mode". ) 2 OFF Gain is fixed at 0 dB. 5. 4 Shading Correction Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the screen. In this case, the shading correction can decrease the color shading. For the shading correction of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided. (Refer to the item "7. 2 (4) (4. 5) Changing the shading correction mode". ) 1 MANU (Manual Shading) Adjust the correction amount on the PROCESS menu by confirming with a monitor or a waveform monitor. (Refer to the "7. 2 (4) (4. 6) Changing the manual shading correction setting". ) 2 OFF The status is no shading correction. * The shading correction is effective when the lens iris or zoom ratio is fixed. OFF for variable lens conditions. 10 6. ITEMS CONTROLLED BY THE SCREEN DISPLAY Item MODE E. Partial read 90fps Partial read 115fps Partial read 120fps Partial read 160fps Partial read 180fps Partial read 240fps Partial read Trigger (1P SNR/SR) Trigger (PW SNR/SR) 1P exposure time MODE MANU MODE Color temperature MANUAL R GAIN MANUAL B GAIN GAMMA Master pedestal R pedestal B pedestal Shading correction mode Manual shading correction H phase adjustment Baud rate Available selections MANU, SS, E. TRG 1P SNR, 1P SR, PW SNR, PW SR, RR OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s 1H/525H~524H/525H, OFF, 2FRM~512FRM 1H/348H~347H/348H, OFF, 2FRM~512FRM 1H/272H~271H/272H, OFF, 2FRM~512FRM 1H/262H~261H/262H, OFF, 2FRM~512FRM 1H/197H~196H/197H, OFF, 2FRM~512FRM 1H/175H~174H/175H, OFF, 2FRM~512FRM 1H/131H~130H/131H, OFF, 2FRM~512FRM OFF, 90fps, 115fps, 120fps, 160fps, 180fps, 240fps, E90fps, E115fps, E120fps, E160fps, E180fps, E240fps , , 0. 01ms~16ms MANU, OFF 0dB~18dB AWB, MANU 3200K, 5600K -100~0~100 -100~0~100 ON, OFF -64~0~64 -64~0~64 -64~0~64 MANU, OFF -128~0~127 -100~0~100 9600 bps, 19200 bps 16 ms OFF 0dB AWB 3200K 0 0 OFF 0 0 0 MANU 0 0 9600 bps Preset value (Factory setting) MANU 1P SNR OFF OFF Electronic shutter Gain White balance OFF Process Sync Option 11 7. MODE SETTING BY THE SCREEN DISPLAY Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized even if the power source is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to be set. 7. 1 Using the Menus When the power is turned on, the normal screen showing only the video signal appears. Change the output to each screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], and [MENU DOWN] buttons. [. . . ] You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with specifications during the Limited Warranty period. All warranty servicing of this product must be made by an ISD Authorized Service Provider. You must pack the Product in its original carton using the original packing material, then insert the original carton containing the Product into another carton with additional packing material before shipping the Product to an ASP. DISCLAIMERS: ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. [. . . ]