User manual TOSHIBA IK-TF7

[. . . ] INSTRUCTION MANUAL 3 CCD CAMERA IK-TF7 For Customer Use Enter below the Serial No. which is located on the bottom of the cabinet. Retain this information for future reference. Model No. : IK-TF7 Serial No. : INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] If the C. TEMP is set to 3200K, set to 5600K. If the message appears with the C. TEMP set to 5600K, change the illumination or use the color temperature conversion filter. AWB NG C. TEMP HIGH 9 Page 9 2004. 04. 05, 8:51 AM Result displayed AWB NG NOT AVAILABLE AWB NG Meaning Automatic white balance adjustment cannot be performed because the shutter speed mode is E. TRG mode. Automatic white balance adjustment cannot be performed for other reasons. Such as no white area is included in an object, etc. 2 MANU (Manual white balance) · Set the MODE to MANU on the WHT BAL menu. (Refer to the item "7. 2 (3) WHT BAL (white balance)". ) · Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a waveform monitor. (Refer to the item "7. 2 (3) (3. 2) Changing each setting in MANU mode". ) 6. 2 Gain When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level. For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. (Refer to the item "7. 2 (2) GAIN (Video gain)". ) 1 MANU (Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from -3dB to 18dB in 1dB steps. (Refer to the item "7. 2 (2) (2. 1) (a) Changing the gain in MANU mode". ) 2 OFF Gain is fixed at 0 dB. 6. 3 Shading Correction Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the screen. In this case, the shading correction can decrease the color shading. For the shading correction of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided. (Refer to the item "7. 2 (4) (4. 5) Changing shading correction mode". ) 1 MANU (Manual Shading) Perform the correction amount setting on the PROCESS menu, confirming with a monitor or a waveform monitor. (Refer to the "7. 2 (4) (4. 6) Changing the manual shading correction setting". ) 2 OFF The status is no shading correction. * The shading correction is effective when the lens iris or zoom ratio is fixed. OFF for variable lens conditions. 10 Page 10 2004. 04. 05, 8:51 AM 7. MODE SETTING BY ON SCREEN DISPLAY Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized when the power is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to be set. 7. [. . . ] ISD reserves the right to substitute Factory Refurbished Parts and / or Factory Refurbished Product in place of those in need of repair. Step-by-step Procedures - How to Obtain Warranty Service [1] Verify operation of the unit by checking the instruction manual [2] If there is a defect in material or workmanship, contact an Authorized Service Provider within 30 days after the product fails to comply with specifications. [3] Arrange for delivery of the product to the ISD authorized service center. Products must be insured and securely packed, preferably in the original shipping carton. [. . . ]