User manual TOSHIBA IK-WB02A

[. . . ] NETWORK CAMERA Model IK-WB02A Safety Precautions *A lens is not supplied with the network camera. For information on the latest products and peripheral devices, refer to the following Web page. I http://www. netcam. toshiba. com GThe above URL is subject to change without prior notice. If the URL changes, refer to the Toshiba website (http://www. cctv. toshiba. com). [. . . ] January 1, 2004 2004 01 01) Indicates time (Hour, Minute, Second). Time is displayed in 24-hour time display. If the camera records more than one image at the same period, the order is indicated with 3-digit number. The bigger the number, the newer (latest) the image. N: Not in Daylight Time D: Daylight (Summer) Time HHMMSS Setting up *** N 5) Enter "Server Path" G Configure FTP server directory to record files . If you do not know the directory, ask for your FTP server administrator. Others 6) Click "Save Settings" button to save configured items G The changes are discarded. 45 Recording Images on FTP Server (Cont. ) IFTP by External Alarm/Motion Detection Installation/Set up Viewing · Listening and Operation Recording Setting up Others You can control the settings to record images for FTP by External Alarm/Motion Detection. G To configure the external alarm/motion detection, select "ON" in "External Alarm Detect" or "Motion Detect" in the alarm settings ( page. 64) G To run the recording, select "Extern Alarm Detection" or "Motion Detection" in "Connection to FTP Enable" ( page. 43). 1) Configure the numbers of frames you want to record for Pre-Recording G Possible numbers of frames are as follows: Enter a number in the range of 0 through 30. 2) Configure the numbers of frames you want to record for Post-Recording G Enter the number between 0 and 1000. NOTE · Numbers of recorded image frame may decrease depending on networking conditions and recording cycle. 3) Configure Interval(s) G Records 1 image per configured recording cycle (second). Setting ranges are 1 through 10. NOTE 46 · Cycle may change depending on Resolution (image size) and networking conditions. 4) Enter "File Name" G Installation/Set up Enter characters in the part described as (keyword). EX (keyword) yyyy mm dd HH MM SS ***N--A. JPG NOTE · You cannot use these characters: \ / : ; , " | ?* < > Followings are the meaning of each part. Viewing · Listening and Operation EX/MD "EX" indicates this is the file for detected external alarm. "MD" indicates this is the file for detected motion. (keyword) yyyymmdd Enter user defined keyword in characters. January 1, 2004 2004 01 01) Indicates time (Hour, Minute, Second). Time is displayed in 24-hour time display. If the camera records more than one image at the same period, the order is indicated with 3-digit number. The bigger the number, the newer (latest) the image. N: Not in Daylight Time D: Daylight (Summer) Time Indicates total number of generated alarm(s). when the number reaches to 99, it returns to 00 and starts adding again. C: Post-Recording images. HHMMSS *** Recording N A/B/C Setting up 5) Enter "Server Path" G Configure FTP server directory to record files. If you do not know the directory, ask for your FTP server administrator. 6) Click "Save Settings" button to save configured items G The changes are discarded. Others 47 Recording Images on FTP Server (Cont. ) IFTP by EXT Control (Recording Data by EXT Control) Installation/Set up Viewing · Listening and Operation Recording Setting up Others You can control the settings to record images for FTP by EXT Control. Select "EXT" in "External Alarm Detect" of the alarm settings ( page. [. . . ] Therefore, its sent to the FTP data sending order is not server. Cannot solve the problems. GPress the reset button. Pressing the reset button returns all the firmware settings of the camera to their default values (initial state at the time of purchase). Perform the following procedure to initialize the camera settings. [. . . ]