User manual TOSHIBA KV-6200A

[. . . ] REFER SERVICING TO QUALIFIED PERSONNEL ONLY. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. USER-INSTALLER CAUTION : YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THIS PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES. NOTE: This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Press the or SHIFT button to blink (12H/24H) and press the + or ­ SET button to go to 12H. DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT ­ + Changes between 12H and 24H each time the + or ­ SET button is pressed. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 12H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/97 THU 5:30:02PMSPA 2 This function enables to indicate and record information from cash register or ATM using a specified option box. Press the or SHIFT button to blink CHAR. LINES and the + or ­ button to go to "6". Press the + or ­ button to select the characters of line number. Each time pressing the + or ­ SET button, the display changes as follows. If you select [DATE] ON: 612345 [TIME] ON: [DATE] OFF: 67812345 [TIME] OFF: } } DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 12H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/97 THU 17:30:32SP A 2 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6 LINE 18 NOTICE PLAYBACK OPERATION RECORDING OPERATION Changes between OFF and ON each time the + or ­ SET button is pressed. When an alarm is input, the day of the week display changes to the alarm number. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] Alarm number 8/28/97 A01 17:30:13 SPA 2 PREPARATION Changes as shown below each time the SET button is pressed. OFF V01 V02 V03 V04 V05 V06 V07 V08 OFF DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) V01 (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] INTRODUCTION INTRODUCTION COUNTER DISPLAYS Counter Memory When the counter is set to "0000" at a location that you want to see again during recording and playback, the tape will stop in the vicinity of "0000" during rewind and fast forward. PREPARATION 1 When the alarm counter is displayed, press the ALARM button to set the display to the counter display. ALARM REC H 3 Press the COUNTER MEMORY button to make "COUNT. M" (Counter Memory) to light. COUNT. M H SP COUNTER MEMORY ALARM RESET SP REC COUNTER MEMORY ALARM RESET 2 RECORDING OPERATION Press the RESET button at the location you want to see. H 4 REV Turn the SHUTTLE dial to set rewind or fast forward after STOP button is pressed. COUNT. M SP H REC SP COUNTER MEMORY ALARM RESET FWD Alarm Memory When you want to view the location where alarm recording was performed. 1 PLAYBACK OPERATION Press the STOP button. ALARM REC SP H 3 REV Turn the SHUTTLE dial to set rewind or fast forward. ALARM M ALARM SP H PLAY PLAY STOP FWD When the tape reaches the alarm recorded position, The VCR automatically enters the still picture mode. 2 NOTICE Press the COUNTER MEMORY button twice to make "ALARM. M" to light. ALARM M ALARM SP H 4 Press the PLAY button. PLAY COUNTER MEMORY ALARM RESET STOP 19 Notes: In the cases shown below, Alarm Memory search may be not carried out. i If the alarm recording is not carried out for more than those listed in the following chart then, the alarm may be skipped. EPA18 mode means that T-120 tape will run 18 hours. However, if you use longer length of video tape which is T-160, it will record up to 24 hours with EPA18 mode. Also, when you use EPA18 mode for recording, you will get 20 fields of video information per second, SPA24 mode will be less than 5 fields video information per second. (Refer to the above chart for the details. ) · When using the T-160 tape, it will be necessary to replace the tape with new one and make a cleaning of the mechanical deck of this VCR more frequently. Because, the thickness of T-160 tape is about 3/4 of T-120 tape, so durability, mechanical strength, etc. of the tape are inferior to T-120 tape. 21 LOADING AND UNLOADING A VIDEO CASSETTE Cassette compartment REC CHECK TIMER REC VIDEO MODE AUTO COLOR B/W PAUSE/STILL REMOTE POWER EJECT OFF REMOTE OPTION TIME LAPSE VCR 4Head 960Hour PLAY STOP REV FWD TAPE REMAIN DISPLAY ­ TIME MODE SET + TRACKING SOFT SHARP MEMORY COUNTER ALARM RESET SHIFT LOCATION SELECT Loading a Cassette i Insert a cassette in the Cassette Compartment. Power goes on automatically and the cassette indicator lights. Unloading a Cassette 1 PLAY Turn the power ON. POWER REC CHECK TIMER REC VIDEO MODE AUTO COLOR B/W REMOTE POWER EJECT OFF REMOTE OPTION TIME LAPSE VCR 4Head 960Hour ON BUZZER OFF PICTURE TAPE REMAIN DISPLAY ­ TIME MODE SET + TRACKING SOFT SHARP MEMORY COUNTER ALARM RESET SHIFT LOCATION SELECT 2 i Press the EJECT button. EJECT Cassette Indicator Safety Tab A video cassette is equipped with a safety tab to prevent accidental erasure. When the tab is removed, recording is not possible. i i Blinks when inserting or removing a cassette. Remains lighted when a cassette is inserted even if the power is turned OFF. Safety tab Screwdriver H REC SP Cassette indicator i If you wish to record on a cassette with the tab removed, use adhesive tape to cover the hole. Adhesive tape 22 NOTICE PLAYBACK OPERATION RECORDING OPERATION PREPARATION 1 2 ON BUZZER OFF PICTURE INTRODUCTION INTRODUCTION RECORDING OPERATION RECORDING 1 2 3 4 Turn on the power for this VCR as well as associated devices of the surveillance system including the video camera and monitor TV. 5 6 7 Insert a video cassette to this VCR. · Check that the safety tab on the video cassette has not been removed. REC CHECK TIMER REC VIDEO MODE AUTO COLOR B/W REMOTE POWER EJECT OFF REMOTE OPTION TIME LAPSE VCR 4Head 960Hour ON BUZZER OFF PICTURE TAPE REMAIN DISPLAY ­ TIME MOD SET SOFT SHARP MEMORY COUNTER ALARM RESET SHIFT PREPARATION Adjust the monitor TV so that the picture from the video camera is displayed properly. Select the recording time mode. H REC ­ TIME MODE SET SP + 1 2 3 Check that the date time display on the monitor TV is correctly displayed. Press the REC button. H RECORDING OPERATION REC 8/28/97 THU 17:30:05SPA 2 1 2 3 REC SP Set the various functions such as timer recording, alarm recording, restart recording, tape end, etc. PLAYBACK OPERATION Notes: i i i i NOTICE i i i When the PAUSE button is pressed during recording, the VCR goes to the pause mode. To release, press either the PAUSE button again or the REC button. [. . . ] Otherwise, You are responsible for payment of all labor charges. Instruction Manual (Owner's Manual): You should read the Instruction Manual (Owner's Manual) thoroughly before operating this Product. Before seeking warranty service, you should check the troubleshooting guide in the Instruction Manual (Owner's Manual) and follow the instructions to correct the problem. Your Responsibilities: This Limited Warranty is subject to the following conditions: 1. [. . . ]