User manual TOSHIBA KV-7960A

[. . . ] Instruction Manual VIRTUAL REAL-TIME & TIME LAPSE VCR KV-7960A PAUSE/STILL POWER TIME LAPSE VCR 4Head 960Hour PLAY STOP REV FWD TAPE REMAIN COUNTER MEMORY ALARM RESET DISPLAY ­ TIME MODE SET SHIFT + TRACKING LOCATION SELECT NOTICE 44 PLAYBACK OPERATION 39 RECORDING OPERATION 23 PREPARATION 11 INTRODUCTION 4 PLEASE READ INTRODUCTION WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] 3 Time : Set to 24-hour cycle at factory. 4 Playback/Recording Time : Playback or Recording time display RECORDING OPERATION It is possible to modify to 12-hour (AM/PM) cycle display. On-Screen Position 8/28/96 WED 17:30:02 A 2 Press the LOCATION SELECT button to adjust the display to desirable position. The display moves in the direction shown by the arrows. LOCATION SELECT Press this button : To down 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 However, during the date-time display screen, pay attention to the following when setting the date and time display positions: When the display is set to an end of the monitor screen as shown in the figure, synchronization instability or color flickering may occur in some monitor TVs. 16 NOTICE PLAYBACK OPERATION 8/28/96 WED 17:30:02 A 2 8/28/96 WED 17:30:02 A 2 Press this button : To right PREPARATION INTRODUCTION INTRODUCTION DISPLAY SCREEN Set the MENU screen to DISPLAY screen, and select or set each item. Before operation, set the MENU screen to DISPLAY screen (See page 13. ). Note: Press the DISPLAY button twice to return from the display screen to the monitor screen. Operation Display Screen DISPLAY (DATE) OFF (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] Monitor Screen PREPARATION Erasing the date display. Press the or SHIFT button to blink DATE and press the + or ­ SET button to go to OFF. Changes between OFF and ON each time the + or ­ SET button is pressed. DISPLAY ­ TIME MODE SET SHIFT + TRACKING LOCATION SELECT 8/28/96 WED 17:30:02 A 2 Erasing the day of the week display. Press the or SHIFT button to blink DAY OF THE WEEK and press the + or ­ SET button to go to OFF. DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT RECORDING OPERATION ­ + Changes between OFF and ON each time the SET button is pressed. DISPLAY (DATE) ON (DAY OF THE WEEK) OFF (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/96 WED 17:30:02 A 2 Erasing the time display. Press the or SHIFT button to blink TIME and press the + or ­ SET button to go to OFF. PLAYBACK OPERATION DISPLAY ­ TIME MODE SET SHIFT + TRACKING Changes between OFF and ON each time the + or ­ SET button is pressed. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) OFF (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/96 WED 17:30:02 A 2 LOCATION SELECT Erasing the speed display. Press the or SHIFT button to blink SPEED and press the + or ­ SET button to go to OFF. DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT + Changes between OFF and ON each time the + or ­ SET button is pressed. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) OFF (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/96 WED 17:30:02 A 2 NOTICE 17 Note: Press the DISPLAY button twice to return from the display screen to the monitor screen. Operation Displaying the VCR number. Press the or SHIFT button to blink VCR and press the + or ­ SET button to set the VCR number. DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT Display Screen Monitor Screen + VCR number 8/28/96 WED 17:30:02 A 2 V01 Displaying the number of alarms. Press the or SHIFT button to blink ALARM and press the + or ­ SET button to go to OFF. DISPLAY ­ TIME MODE SET SHIFT TRACKING LOCATION SELECT + Displaying the hour display. or SHIFT button to blink (12H/24H) and Press the press the + or ­ SET button to go to 12H. DISPLAY TIME MODE SET SHIFT TRACKING LOCATION SELECT ­ + Changes between 12H and 24H each time the + or ­ SET button is pressed. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 12H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/96 WED 5:30:02PM A 2 This function enables to indicate and record information from cash register or ATM using a specified option box. Press the or SHIFT button to blink CHAR. LINES and the + or ­ button to go to "6". Press the + or ­ button to select the characters of line number. Each time pressing the + or ­ SET button, the display changes as follows. If you select [DATE] ON: 612345 [TIME] ON: [DATE] OFF: 67812345 [TIME] OFF: } } DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 12H (CHAR. LINES) 6 MENU=[DISPLAY] 8/28/96 WED 17:30:32 A2 1 LINE 2 LINE 3 LINE 4 LINE 5 LINE 6 LINE 18 NOTICE PLAYBACK OPERATION RECORDING OPERATION Changes between OFF and ON each time the + or ­ SET button is pressed. When an alarm is input, the day of the week display changes to the alarm number. DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) OFF (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] Alarm number 8/28/96 A01 17:30:13 A 2 PREPARATION Changes as shown below each time the SET button is pressed. OFF V01 V02 V03 V04 V05 V06 V07 V08 OFF DISPLAY (DATE) ON (DAY OF THE WEEK) ON (TIME) ON (SPEED) ON (VCR) V01 (ALARM) ON (12H/24H) 24H (CHAR. LINES) 6 MENU=[DISPLAY] INTRODUCTION INTRODUCTION COUNTER DISPLAYS Counter Memory When the counter is set to "0000" at a location that you want to see again during recording and playback, the tape will stop in the vicinity of "0000" during rewind and fast forward. PREPARATION 1 When the alarm counter is displayed, press the ALARM button to set the display to the counter display. ALARM REC H 3 Press the COUNTER MEMORY button to make "COUNT. M" (Counter Memory) to light. COUNT. M H SP COUNTER MEMORY ALARM RESET SP REC COUNTER MEMORY ALARM RESET 2 RECORDING OPERATION Press the RESET button at the location you want to see. H 4 REV Turn the SHUTTLE dial to set rewind or fast forward after STOP button is pressed. COUNT. M SP H REC SP COUNTER MEMORY ALARM RESET FWD Alarm Memory When you want to view the location where alarm recording was performed. 1 PLAYBACK OPERATION Press the STOP button. ALARM REC SP H 3 REV Turn the SHUTTLE dial to set rewind or fast forward. ALARM M ALARM SP H PLAY PLAY STOP FWD When the tape reaches the alarm recorded position, The VCR automatically enters the still picture mode. 2 NOTICE Press the COUNTER MEMORY button twice to make "ALARM. M" to light. ALARM M ALARM SP H 4 Press the PLAY button. PLAY COUNTER MEMORY ALARM RESET STOP 19 Notes: In the cases shown below, Alarm Memory search may be not carried out. [. . . ] Recording does not continue automatically after restoring power following a power failure. Black/white picture appears in playback through color camera signals are recorded. i Has DISPLAY MODE been set?i Did the power failure continue for more than 10 days?i Playback is carried out with the VIDEO MODE switch set to B/W i Recording is carried out with the VIDEO MODE switch set to B/W i Playback is carried out with the VIDEO MODE switch set to COLOR i Recording is carried out with the VIDEO MODE switch set to COLOR position. [. . . ]