User manual TOSHIBA MA-1535-2

[. . . ] TEC Electronic Cash Register MA-1535-2 SERIES Owner's Manual Owner's Manual Supplement V2 "This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. " "Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. " FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. [. . . ] Information about the EFT media will not be printed on the slip. 9-31 '(02 %DUJDLQ VDOHV RQ HYHU\ 7XHVGD\ &RPH WR VDYH PRQH\ , 7(0 &/ 70 9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11149 9. 40 Sale Finalization by Electronic Fund Transfer (EFT) (6) Post Authorization Only a cashier with Supervisor status is allowed this operation. · Without Card Number Entry [POST AUTH] Card Slide NOTE1 NOTE1 ECR wait condition |Sale Amount| [#/NS] NOTE1 |Authorization Code| [#/NS] (Max. 11 digits) If the EFT terminal responds "APPROVAL" If the EFT terminal responds "DECLINE" Print marchant draft · With Card Number Entry [MANUAL CARD#] NOTE2 [POST AUTH] NOTE1 |Card No. | [#/NS] (Max. 25 digits) NOTE1 |Expiration Date| [#/NS] (Max. 4 digits; Month/Year) |Sale Amount| [#/NS] NOTE1 ECR wait condition NOTE1 |Authorization Code| [#/NS] (Max. 11 digits) If the EFT terminal responds "APPROVAL" If the EFT terminal responds "DECLINE" Print marchant draft NOTES: 1. Pressing the [C] key at this point will display the message "EFT CANCEL". Pressing the [C] key again will restore the ECR to the condition being ready for the [POST AUTH] key entry. Pressing the [C] key at this point will restore the ECR to the condition being ready for the [MANUAL CARD#] key entry. Values 0 to 9 and A to Z should be used to enter the Authorization Code. The Receipt Issue operation is unavailable. Training Cashiers are unacceptable to the EFT terminal. Information about the EFT media will not be printed on the slip. By the program option, the symbol instead of the card No. and the expiration date will be printed on both the receipt and the journal at the sale finalization by EFT. When the program option "the symbol instead of the card No. and the expiration date is printed" has been selected, the card No. and the expiration date are printed as shown below. Card No. : Numeric values are printed in the lower 4 digits and the symbol is printed in the other digits. (Example) 1234 Expiration date: The symbol is printed in all the digits instead of numeric values. The data that is printed on the receipts issued from the receipt printer will be printed on the journal, except for the signature and the agreement message portions. 9-32 9. [. . . ] CONDITION OPERATION Anytime outside a sale Control Lock: X or Z Repeat for other PLUs. 90 [ST] |PLU Code| [PLU] |Stock Quantity| (0. 001 to 9999. 999) [R/A] or [LOAN] (When adding the stock quantity. ) [ST] [PO] or [PICK-UP] (When subtracting the stock quantity. ) NOTE: PLU programming should be done before this operation. Example) To change the stock quantity of the following PLU. Key Operation: Control Lock: X or Z, Enter 90 and depress the [ST] key. 01000000010101 (PLU Code) [PLU] 20 (Stock Quantity) [R/A] or [LOAN] (When adding the stock quantity. ) [ST] (To complete this submode. ) 4-33 5. PROGRAMMED DATA VERIFICATION EO1-11149 5. [. . . ]