User manual TOSHIBA MAGNIA 3200

[. . . ] Remove two M2x8 silver screws securing the connector cover. Remove the connector cover and the connector from the CD-R/W/DVD-ROM drive. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite Pro 6000 Series MEMORY MODULE REMOVAL Memory slot cover TM M2. 5x4 black screws 1. Remove two M2. 5x4 black screws securing the memory cover. Lift out the memory slot cover. Memory clips 4. [. . . ] Disconnect the bluetooth card from the system board. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite Pro 6000 Series MODEM BOARD REMOVAL M2x4 brass screws Modem harness Modem slot cover TM M2. 5x4 black screw 1. Remove one M2. 5x4 black screw securing the modem slot cover. Insert your finger nail or the case separator into the notched side of the cover and lift up to release the two latches securing the left side of the modem slot cover. Modem board 3. Disconnect the modem harness from the modem board. Remove two M2x4 brass screws securing the modem board. Lift up the modem board to disconnect it from the system board. HDD REMOVAL HDD cover M2. 5x6 black flat head screw Plastic Tab HDD pack 1. Remove one M2. 5x6 black flat head screw securing HDD cover. Unfold the plastic tab and pull to remove the HDD from the bay. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite Pro 6000 Series HDD REMOVAL HDD bracket Latch TM KEYBOARD REMOVAL Keyboard HDD M3x4 brass flat head screws Keyboard holder 1. Turn the computer right side up and open the display panel. Using the case separator, unlatch the keyboard holder at the top of the keyboard. 5. Remove two M3x4 brass flat head screws securing the HDD to the bracket and remove the HDDbracket. KEYBOARD REMOVAL Keyboard Keyboard cable PJ445 M2. 5x2. 6 black screws 3. Disconnect the power supply board from the system board. Power supply board SYSTEM BOARD REMOVAL M2. 5x4 black flat head screw SD/Sound board 1. Disconnect the sound interface cable from PJ103 and the SD interface cable from PJ150 on the SD/Sound board. Remove one M2. 5x4 black flat head screw securing the SD/Sound board. PJ803 HDD guide assy SD interface cable Sound interface cable M2. 5x4 black flat head screws M2. 5x6 flat head black screw M2. 5x6 black flat head screws Select bay cover DC-IN jack harness 1. Remove one M2. 5x6 black flat head screw securing the HDD guide assembly and lift out the HDD guide assembly. Remove three M2. 5x6 black flat head screws securing the select bay cover and lift out the select bay cover. 3. Disconnect following cables from the system board: -Sound interface cable from PJ103 -SD interface cable from PJ150 -DC-IN jack harness from PJ803 4. Remove four M2. 5x4 black flat head screws securing the system board. Lift out the system board. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite Pro 6000 Series MEMBRANE SWITCH REMOVAL Membrane switch assy Left and right speakers TM SPEAKERS REMOVAL M2. 5x4 black flat head screws 1. Remove three M2. 5x4 black flat head screws securing the membrane switch. Lift out the membrane switch assembly. M2. 5x4 black flat head screws 1. [. . . ] Turn the display assembly right side up and open the LCD panel. Lift out the left and right speakers. Tough Enough for Today's World. TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite Pro 6000 Series 14. 1" DISPLAY MASK REMOVAL Latch M2x3 silver screws M2x5 silver screws M2x3 silver screws M2x5 silver screws TM FL INVERTER AND 14. 1" LCD REMOVAL LCD module assy Display mask LCD Mask seals 1. Remove two mask seals at the bottom corners of the display assembly using a pair of fine-tipped tweezers. Remove two M2. 5x6 black flat head screws securing the display mask. [. . . ]