User manual TOSHIBA MAGNIA 510D

[. . . ] Slide the release lever in the direction of the arrow. Pull out the modular bay device in the direction of the arrow. Remove four M2. 5x4 black screws securing the DVD-ROM/CDR-W to the bracket. Slide the DVD-ROM/CDR-W out of the bracket. [. . . ] Disconnect the DVD-ROM/CDR-W connector from the drive. Tough Enough for Today's World TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite 3000 Series HDD REMOVAL HDD REMOVAL M3x4 silver screws HDD bracket TM Insulator HDD connector M2. 5x3 black screws 1. Remove two M2. 5x3 black screws securing HDD assembly. Slide the HDD assembly in the direction of the arrow to disconnect from the system board. Lift the HDD assembly out of the HDD bay. Remove two M3x4 silver screws securing the HDD bracket to the drive and lift off the bracket. Peel off the HDD insulator. MEMORY MODULE REMOVAL Memory clips Memory cover M2x3 Black screws 1. Remove two M2x3 black screws and remove the memory cover. Memory module 3. Spread the memory clips securing the memory module and pull the memory module out of the connector on a 45 degree angle. Tough Enough for Today's World TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite 3000 Series KEYBOARD REMOVAL Wireless switch Control board cable Display panel TM JP1 Keyboard holder Board switch Case separator 1. Using the case separator, unlatch the keyboard holder at the top of the keyboard. Keyboard holder M2. 5x3 silver screws 3. Disconnect the control switch/LED board cable from the keyboard holder. Unlatch the top cover from the bottom cover. Tough Enough for Today's World TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite 3000 Series VIDEO BOARD REMOVAL JP8 Video board TM MODEM BOARD REMOVAL JP11 System board RJ11 cable Modem board JP13 1. Disconnect the video board from JP8 and JP11 on the system board. 1. Disconnect the modem board from JP13 on the system board. Disconnect the RJ11 cable from the modem board. WIRELESS LAN CARD REMOVAL Mini PCI Clips Wireless LAN card 1. Push the Mini PCI slot clips outward and pull the Wireless LAN card out of the connector on a 30 degree angle. Tough Enough for Today's World TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite 3000 Series SYSTEM BOARD REMOVAL Hex screws Stud screws TM System board Metal shield M2. 5x4 brass screws 1. Remove the following eleven screws securing the system board: - 2 M2. 5x4 brass screws securing the metal shield - 5 M2. 5x4 brass screws securing the HDD shield - 1 M2. 5x4 brass screw on the system board - 4 stud screws from the CPU socket 2. Remove four hex screws at the back of the computer securing the system board. Lift out the system board. Tough Enough for Today's World TOSHIBA FIELD REPLACEABLE UNIT DOCUMENTATION Satellite 3000 Series 14" DISPLAY MASK REMOVAL Latch TM FL INVERTER AND 14" LCD REMOVAL LCD module Display mask LCD Mask seals 1. Remove two rubber seals at the top corners of the display assembly and two mask seals at the bottom corners of the display assembly. Remove four M2. 5x5 silver screws securing the display mask. [. . . ] Remove four M2. 5x5 silver screws securing the display mask. There are 21 latches securing the display mask. Carefully insert your fingers between the display mask and the LCD module and pry open the latches starting from the bottom six latches, to the five latches on the right and left sides, ending with the top six latches. Tape LCD/ FL cable M2x4 brass screws FL cable FL inverter board 1. Peel off the tape securing the FL cable. [. . . ]