User manual TOSHIBA RAS-13SAX SERVICE MANUAL

[. . . ] T O S H IB A S E R V IC E M A N U A L F IL E N O . A 0 0 -9 7 0 1 A IR -C O N D IT IO N E R R A S -1 3 S K -E R A S -1 3 S K X S P L IT W A L L T Y P E R A S -1 3 S A -E R A S -1 3 S A X P R IN T E D IN J A P A N , F e b . , 1 9 9 7 ToM o CONTENTS 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONSTRUCTION VIEWS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Bend the connection pipe within a radius of 30 mm. Installation plate · Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit. · Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. · Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) · When bending a pipe, carefully do it not to crush it. ­ 26 ­ 8-4-5. Indoor Unit Installation (1) Pass the pipe through the hole in the wall, and hook the indoor unit on the installation plate at the upper hooks. (2) Swing the indoor unit to right and left to confirm that it is firmly hooked up on the installation plate. (3) While pressing the indoor unit onto the wall by the lower part, hook it up on the installation plate by the lower part. Pull the indoor unit toward you by the lower part to confirm that it is firmly hooked up on the installation plate. (1) 8-4-6. Drainage (1) Run the drain hose sloping downwards. NOTE : · Hole should be made at a slight downward slant to the outdoor side. Do not rise the drain hose. Do not form the drain hose into the wared shape. 50 mm or more Do not put the drain hose end into water. Do not put the drain hose end in the drainage ditch. Hook here 1 Installation plate (2) Fig. 8-4-17 (2) Put water in the drain pan and make sure that the water is drained outdoors. (3) When connecting extension drain hose, insulate the connecting part of extension drain hose with 5 shield pipe. 5 Shield pipe Hook Push Fig. 8-4-15 · For detaching the indoor unit from the installation plate pull the indoor unit toward you while pushing its bottom up by the specified parts. Drain hose Inside the room Extension drain hose Fig. 8-4-18 CAUTION Push Push Arrange the drain pipe for proper drainage from the unit. Improper drainage can result in damage to property. This air conditioner has the structure designed to drain water collected from dew, which forms on the back of the indoor unit, to the drain pan. Therefore, do not store the power cord and other parts at a height above the drain guide. Wall Drain guide Fig. Outdoor Unit t Installation place · A place which provides the spaces around the outdoor unit as shown in the diagram in page 23. · A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration. · A place where the operation noise and discharged air do not disturb your neighbors. · A place which is not exposed to a strong wind. [. . . ] Outdoor Unit (RAS-13SA-E, RAS-13SAX) No. Part name Common procedure Procedure 1) Stop the operation of air-conditioner, and disconnect the power cord from the AC supply. (2- ST1T ø4 x 10 ) 3) Remove the cord clamp (2- ST2T ø4 x 12 ) and remove the connecting cable. (8- ST1T ø4 x 10 with nylon washer) · Pull the front lower portion toward you, and remove it pulling out upward. [. . . ]