User manual TOSHIBA RAS-16SAVP-E SERVICE MANUAL

[. . . ] A06-011 SERVICE MANUAL AIR-CONDITIONER SPLIT TYPE Indoor Unit <High Wall, Heat Pump Type> (Standard Type) Outdoor Unit <Heat Pump Type> RAS-B10SKVP-E RAS-B13SKVP-E RAS-B16SKVP-E (North Europe Type) RAS-10SAVP-E RAS-13SAVP-E RAS-16SAVP-E RAS-10SAVP-ND RAS-13SAVP-ND RAS-16SAVP-ND RAS-10SKVP-ND RAS-13SKVP-ND RAS-16SKVP-ND R410A PRINTED IN JAPAN, Fub, 2007 ToMo CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT R410A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Decide the installation plate mounting position on the wall. Mark the corresponding pipe hole wall positions according to the positioning marks ( ð ) on the installation plate. Drill the pipe holes (Ø65 mm) slightly slanted downward to the outside. Remote controller · Should be placed where there are no obstacles, such as curtains, that may block the signal. · Do not install the remote controller in a place exposed to direct sunlight or close to a heating source, such as a stove. · Keep the remote controller at least 1 m away from the nearest TV set or stereo equipment. (This is necessary to prevent image disturbances or noise interference. ) · The location of the remote controller should be determined as shown below. Indoor unit NOTE : · When drilling into a wall that contains a metal lath, wire lath or metal plate, be sure to use a pipe hole brim ring sold separately. Mounting the installation plate Anchor bolt holes (Side view) (Top view) Indoor unit 25 mm 91 mm Pipe hole Reception range Remote controller Reception range Remote controller Pipe hole Indoor unit 6 Mounting screw 1 Installation plate *: Axial distance Fig. 10-3-3 ­ 58 ­ When the installation plate is directly mounted on the wall 1. Securely fit the installation plate onto the wall by screws with the upper and lower catches. To mount the installation plate on a concrete wall use anchor bolts. Drill the anchor bolt holes as illustrated in the above figure. Place the level at the top end of the installation plate, and check that the plate is horizontal. 10-3-3. The supply voltage must be the same as the rated voltage of the air conditioner. Prepare a power source for the exclusive use of the air conditioner. NOTE : · Wire type : More than H07RN-F or 60245IEC66 (1. 0mm²) CAUTION When installing the installation plate with mounting screws, do not use the anchor bolt holes. Otherwise the unit may fall down and result in personal injury and property damage. CAUTION A switch or circuit breaker that can disconnect all poles must be included in the fixed wiring. Be sure to use an approved circuit breaker or switch. NOTE : · Make sure the wire length is sufficient before performing wiring work. Anchor bolt Projection 15mm or less 10-3-4. Wiring Connection How to connect the connecting cable Wiring the connecting cable can be carried out without removing the front panel. Open the air inlet grille upward and pull it toward you. Remove the terminal cover and cord clamp. Insert the connecting cable (or as according to local regulations/codes) into the pipe hole on the wall. Pull the connecting cable through the cable slot on the rear panel so that it protrudes about 15 cm out of the front. Insert the connecting cable fully into the terminal block and secure it tightly with screws. Make a loop with the earth wire under the terminal block and secure it with the earth screw. [. . . ] 43067115 4306S949 4306S950 4306S951 Description Clamp, Cord P Board Ass'y . C. Outdoor Unit RAS-10SAVP-E, RAS-13SAVP-E, RAS-16SAVP-E 11 4 28, 29 30, 31 2 47 45 44 46 10 43 38 14, 15, 17, 18, 20, 21, 23, 24, 25 36 33 34 35 1 5 37 6 48 27 13, 16, 19, 22 3 9 8 32 40 41 42 39 7 ­ 112 ­ The parts in the following parts list are conformed to RoHS. Therefore be sure to use the following parts for repairing and replacing. 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 Part No. [. . . ]