User manual TOSHIBA RAS-3M26GAV-E DATA BOOK

[. . . ] PARTS REPLACEMENT 10-1 Indoor Unit 10-2 Outdoor Unit 11. EXPLODED VIEWS AND PARTS LIST 11-1 11-2 11-3 11-4 11-5 11-6 11-7 Indoor Unit (E-Parts Assy) (For RAS-13GKHP-ES2) Indoor Unit (E-Parts Assy) (For RAS-13NKHP-AS2) Indoor Unit (E-Parts Assy) (For RAS-13GKP-ES2) Indoor Unit (E-Parts Assy) (For RAS-13NKP-AS2) Indoor Unit Outdoor Unit (RAS-3M26GAV-E, RAS-13N2AH-AS2) Outdoor Unit (RAS-13GA-ES2, RAS-13N2A-AS2) · This air conditioner is charged with HFC (R410A) that doesn't deplete the Ozone layer. · This air conditioner requires special installation for the refrigerant R410A. -2- FILE NO. SPECIFICATIONS MODEL ITEM Capacity 220V kW Phase Power source Power consumption Power factor Running current Indoor Outdoor V Hz kW % A A A lit/h dB dB kg mm mm m m RAS-13GKHP-ES2 RAS-13NKHP-AS2 Height Dimensions Net weight Evaporator type Indoor fan type High fan Airflow volume Medium fan Low fan Fan motor output Air filter OUTDOOR UNIT Height Dimensions Net weight Condenser type Outdoor fan type Airflow volume Fan motor output Compressor Safety device Louver type Usable outdoor temperature range °C 15 ~ 43 Model Output W m /h 3 RAS-13GKHP-ES2 / RAS-3M26GAV-E RAS-13NKHP-AS2 / RAS-13N2AH-AS2 Cooling 240V 3. 82 220V 4. 20 1 220 - 240 50 1. 15 98 5. 20 1. 19 96 5. 00 30 2. 0 41/35/31 50 51 50 R410A 1. 08 Capillary tube 12. 7 Flare connection 6. 35 Flare connection 15*1 6 51 1. 14 96 0. 15 5. 27 5. 18 1. 18 95 3. 74 Heating 240V 4. 26 RAS-13GKP-ES2 / RAS-13GA-ES2 RAS-13NKP-AS2 / RAS-13N2A-AS2 Cooling 220V 3. 75 240V 3. 75 1. 13 98 5. 10 26 1. 17 97 4. 90 Starting current Moisture removal Noise Refrigerant Indoor (H/M/L) Outdoor (220-240V) Name of refrigerant Rated amount Gas side size Connection type Liquid side size Interconnection Connection type Maximum length pipe (One way) Maximum height difference INDOOR UNIT 50 0. 98 51 Refrigerant control RAS-13GKP-ES2 RAS-13NKP-AS2 275 790 218 10 Finned tube Cross flow fan mm mm mm kg Width Depth m3/h m /h 3 630 520 430 650 550 490 20 Honeycomb woven filter with PP frame 630 520 430 m3/h W RAS-3M26GAV-E, RAS-13N2AH-AS2 mm mm mm kg 39 Finned tube Propeller fan 2120 2200 42 PA150X2C-4FT 1100 Fuse, Overload relay Automatic louver -10 ~ 24 2120 2200 550 780 290 RAS-13GA-ES2, RAS-13N2A-AS2 Width Depth 38 2030 30 2150 W 15 ~ 43 -3- FILE NO. [. . . ] 8-4-7 Earth line 60 mm 10 mm CAUTION · Be sure to refer to the wiring system diagram labeled inside the front panel. · Check local electrical cords and also any specific wiring instructions or limitations. For Heat pump Terminal cover Cord clamp Terminal block 10 mm 50 mm Stripping length of the connecting cable Fig. 8-4-8 NOTE · Use stranded wire only. · Wire type : H07 RN-F or more <How to install the air inlet grille on the indoor unit> · When attaching the air inlet grille, the contrary of the removed operation is performed. Screw Connecting cable abo 4 4 12 3 12 3 ut 1 5 cm Earth line Screw Screw Connecting cable Fig. 8-4-5 Earth line 80 mm 10 mm 70 mm Fig. 8-4-9 10 mm 10 mm 50 mm Stripping length of the connecting cable Fig. Piping and drain hose installation <Piping and drain hose forming> * Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) Rear right 4 mm How to fix the drains cap 1) Insert hexagonal wrench (4 mm) in a center head. Left Bottom right Right Die-cutting Front panel slit Bottom left Changing drain hose Rear left Piping preparation Fig. 8-4-12 2) Firmly insert drains cap. No gap Do not apply lubricating oil (refrigerant machine oil) when inserting the drain cap. Application causes deterioration and drain leakage of the plug. · Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) · When bending a pipe, carefully do it, not to crush it. NOTE · Hole should be made at a slight downward slant on the outdoor side. Do not rise the drain hose. Do not form the drain hose into a wavy shape. 8-5. Installation place · A place which provides the spaces around the outdoor unit as shown in the left diagram. · A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration. · A place where the operation noise and discharged air do not disturb your neighbors. · A place which is not exposed to a strong wind. · A place free of a leakage of combustible gases. · A place which does not block a passage. · When the outdoor unit is to be installed in an elevated position, be sure to secure its feet. [. . . ] Part name Procedures Remarks 4 Heat exchanger 1) Remove the front panel, electrical part and the horizontal louver following procedure 3. 2) Remove the pipe holder at the rear side of main unit. 3) Remove the 2 screws on the heat exchanger at the base bearing. 4) Remove the 2 screws on the heat exchanger at the 2 fixed plates (upper and lower) from the back body, and then pull out the upper side of the heat exchanger slowly. 2 Pipe holder 3 2-Screws 4 2-Screws 5 Cross flow fan 1) Remove the front panel, electrical part, horizontal louver and the heat exchanger following procedure 4. [. . . ]