User manual TOSHIBA RAV-717KED SERVICE MANUAL

[. . . ] If an above action is executed during the fan operation, the protective control works to stop the unit operation, and the check code "P12" may be issued. When the desired operation has finished, be sure to reset the system to clear "P12" error code using the leak breaker of the indoor unit. Then push the operation stop button of the remote controller to return to the usual operation. CONTENTS SAFETY CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2007 [F06 error] Are connections of TE/TS sensor connectors of CDB CN604/CN605 normal?YES Are characteristics of TE/TS sensor resistance values normal?YES NO Correct connection of connector. * (For RAV-SM563AT-E, SM803AT-E, CN600 TE sensor and CN603 TS sensor) NO Replace TE and TS sensors. Check CDB. Defect Replace ® * Refer to Characteristics-3. [F04 error] Is connection of TD sensor connector of CDB CN600 normal?YES Are characteristics of TD sensor resistance value normal?YES NO Correct connection of connector. * (For RAV-SM563AT-E, SM803AT-E, CN601 TD sensor) NO Replace TD sensor. Check control P. C. Defect Replace ® * Refer to Characteristics-4. [F08 error] Is connection of TO sensor connector of CDB CN601 normal?YES Are characteristics of TO sensor resistance value normal?YES NO Correct connection of connector. * (For RAV-SM563AT-E, SM803AT-E, CN602 TO sensor) NO Replace TO sensor. Check CDB. Defect Replace ® * Refer to Characteristics-5. ­ 95 ­ Revised : Mar. 2007 [L29 error] Are connections of CDB CN800 and CDB IPDU CN06 connectors normal?YES NO Improve and delete the cause. Check and correct circuit cables. Check IPDU. Defect Replace * For RAV-SM563AT-E, SM803AT-E, replace control P. C. board. ® ­ 97 ­ Revised : Mar. 2007 [P04 error] Is high-voltage protective operation by TE sensor normal?YES NO Is connection of cabling connector normal?YES NO Correct connection of cabling connector. Check TE sensor. Defect Replace Does cooling outdoor fan normally operate?YES Do not TD and TO sensors come off the detection part?YES Are characteristics of TD, TO, TC sensor resistance values normal?NO ® Correct coming-off. Replace TD, TO, and TC sensors. * Refer to Characteristics-3 and 4. Check CDB. Defect Replace * For RAV-SM563AT-E, SM803AT-E, replace control P. C. [. . . ] When the power cord size does not match with Pshape clamp, procure the most appropriate one at the local site. ­ 189 ­ No. Photo / Explanatory diagram Procedure 3 Assembly Return a set of the refrigeration cycle assembly into the outdoor unit base plate and reassemble sound insulation board, partition plate assembly, fan motor assembly, and side cabinet (R/L) as original. Fix the thermostat fixing plate to the side cabinet (R), built in the inverter assembly, and then connect various cables. After then, incorporate front cabinet, upper cabinet, wiring cover, and valve cover as before. Return a set of the refrigeration cycle assembly into the outdoor unit base plate, and assemble sound insulation board, partition plate assembly, fan motor assembly, and side cabinet (R/L) as original. 3-1 Thermostat fixing plate Side cabinet (R) Using screws (Self-tapping screw type-B Ø4 × 8mm, stainless), fix the thermostat fixing plate to the side cabinet (R). 3-2 Do not make cord heater loose. [. . . ]