User manual TOSHIBA RAV-SM402MUT-E INSTALLATION MANUAL

[. . . ] AIR CONDITIONER (SPLIT TYPE) Installation Manual Indoor Unit Model name: 4-way Air Discharge Cassette Type RAV-SM402MUT-E RAV-SM452MUT-E RAV-SM562MUT-E Not accessible to the general public Installation manual Air conditioner (Split type) 1 English Please read this Installation Manual carefully before installing the Air Conditioner. · This Manual describes the installation method of the indoor unit. · For installation of the outdoor unit, follow the Installation Manual attached to the outdoor unit. ADOPTION OF NEW REFRIGERANT This Air Conditioner is a new type which adopts a new refrigerant HFC (R410A) instead of the conventional refrigerant R22 in order to prevent destruction of the ozone layer. CONTENTS Accessory parts and Parts to be procured locally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1 2 3 4 5 6 7 8 9 10 PRECAUTIONS FOR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Be sure to comply with local regulations on running the wire from outdoor unit to indoor unit (size of wire and wiring method etc. ) · Use the power cord and Inter-connecting wire of specified thickness, type, and protective devices required. REQUIREMENT · For power supply wiring, strictly conform to the Local Regulation in each country. · For wiring of power supply of the outdoor units, follow the Installation Manual of each outdoor unit. · Never connect 220­240V power to the terminal blocks ( A , B , etc. ) for control wiring. (Otherwise, the system will fail. ) · Perform the electric wiring so that it does not come to contact with the high-temperature part of the pipe. The coating may melt resulting in an accident. · After connecting wires to the terminal blocks, provide a trap and fix wires with the wire clamp. · Run the refrigerant piping line and control wiring line in the same line. · Do not turn on the power of the indoor unit until vacuuming of the refrigerant pipes completes. How to wire 1. Connect the connecting wire to the terminal as identified with their respective numbers on the terminal block of indoor and outdoor unit. H07 RN-F or 245 IEC 66 (1. 5 mm2 or more) 2. Insulate the unsheathed redundant cords (conductors) with electrical insulation tape. Process them so that they do not touch any electrical or metal parts. For inter-unit wiring, do not use a wire jointed to another on the way. 16 English-16 6 · · · · ELECTRICAL WORK Wire connection REQUIREMENT Be sure to connect the wires matching the terminal numbers. Be sure to pass the wires through the bushing of wiring connection port of the indoor unit. 100mm) on a wire to hang down the electric parts box at servicing, etc. The low-voltage circuit is provided for the remote controller. (Do not connect the high-voltage circuit) · Remove the cover of the electric parts box by taking off the mounting screws (3 positions) and pushing the hooking section. (The cover of the electric parts box remains hanged to the hinge. ) · Connect the indoor/outdoor connection wires and remote controller wire to the terminal block of the electric parts box. (Do not apply tension to the connecting section of the terminal block. ) · Tighten the screws of the terminal block, and fix the wires with cord clamp attached to the electric parts box. (Do not apply tension to the connecting section of the terminal block. ) · Using the attached thermal insulation material, seal the pipe connecting port. · Mount the cover of the electric parts box without pinching wires. (Mount the cover after wiring on the ceiling panel. ) Screws Electric parts box P board . C. Screw Cover of electric parts box Hooking section Thermal insulation to wiring connecting port Indoor/Outdoor crossover wire/ Remote controller terminal block AB Adhered surface Heat insulator A Power supply terminal block 123 Notched section A B 1 2 3 Cord clamp Heat insulator B Wiring on the ceiling panel As per the Installation Manual of the ceiling panel, connect the connector (2P: Red) of the ceiling panel to the connector (5P: White) onto the P board . C. [. . . ] E03/L07/L03/L08 alarm check locations and error description L30 SIM Abnormal external input into indoor unit (interlock) Indoor Entire stop Operation continued (thermostat OFF) L31 SIM Phase sequence error, etc. Outdoor P01 P03 l ¥ ¥ ¥ ¥ ALT ALT Indoor unit fan error Outdoor unit discharge temp. error Outdoor unit highpressure system error Open phase detected Heat sink overheat Indoor unit water overflow detected Gas leakage detected Indoor Outdoor Entire stop Entire stop l l l l ¥ P04 ALT Outdoor Entire stop P05 (P04) P07 ALT ALT Outdoor Outdoor Entire stop Entire stop P10 l ¥ ¥ ¥ ¥ ¥ ¥ ¥ ALT Indoor Entire stop P15 (P29) P19 (P04) P20 (L29) P22 l l l l l l l ALT Outdoor Outdoor (Indoor) Outdoor Outdoor Entire stop Auto-reset (Auto-reset) Entire stop Entire stop ALT 4-way valve error ALT ALT High-pressure protective operation Outdoor unit fan error P26 ALT Outdoor unit inverter Idc activated Outdoor Entire stop P29 ALT Outdoor unit position error Outdoor Entire stop Entire stop Auto-reset P31 ALT Other indoor unit error Indoor Check codes in parentheses ( ) are displayed when connected to are outdoor unit other than the new SDI series 4 (RAV-SP ¡ : Lighting, ¥ : Flashing, l : OFF, « : The air conditioner automatically enters the auto-address setting mode. ALT : When two LEDs are flashing, they flash alternately. SIM : When two LEDs are flashing, they flash in synchronization. [. . . ]