User manual TOSHIBA RBC-FDP3-PE INSTALLATION MANUAL

[. . . ] PARTS REPLACEMENT 10-1 Indoor Unit 10-2 Outdoor Unit 11. EXPLODED VIEWS AND PARTS LIST 11-1 11-2 11-3 11-4 11-5 11-6 11-7 Indoor Unit (E-Parts Assy) Indoor Unit Outdoor Unit (RAS-13UAH-ES3, RAS-13UAH-AS3) Outdoor Unit (RAS-10UAH-ES3, RAS-10UAH-AS3) Outdoor Unit (RAS-13UA-ES3, RBC-FDP3-PE) Outdoor Unit (RAS-10UA-ES3, RAS-10UA-AS3) Outdoor Unit (RAS-07UA-ES3) This air conditioner is charged with HFC (R410A) that doesn't deplete the Ozone layer. This air conditioner requires special installation for the refrigerant R410A. -2- FILE NO. SPECIFICATIONS MODEL ITEM Capacity 220V kW Phase Power source Power consumption Power factor Running current Indoor Outdoor V Hz kW % A A A lit/h dB dB kg mm mm 49 51 49 R410A 0. 95 Capillary tube 12. 7 Flare connection 6. 35 Flare connection m m RAS-13UKHP-ES3, AS3 Height Dimensions Net weight Evaporator type Indoor fan type High fan Air volume Medium fan Low fan Fan motor output Air filter OUTDOOR UNIT Height Dimensions Net weight Condenser type Outdoor fan type Airflow volume Fan motor output Compressor Safety device Louver type Usable outdoor temperature range C 15 ~ 43 Model Output W m /h 3 RAS-13UKHP-ES3, AS3 RAS-13UAH-ES3, AS3 Cooling 240V 3. 60 220V 4. 20 1 220 - 240 50 1. 10 98 4. 95 1. 12 97 4. 65 27 2. 0 41/35/31 51 1. 14 97 0. 15 5. 20 4. 95 1. 18 96 3. 60 Heating 240V 4. 26 RAS-13UKP-ES3, AS3 RAS-13UA-ES3, AS3 Cooling 220V 3. 75 240V 3. 75 1. 13 98 5. 10 28 1. 17 97 4. 90 Starting current Moisture removal Noise Refrigerant Indoor (H/M/L) Outdoor (220-240V) Name of refrigerant Rated amount Gas side size Connection type Liquid side size Interconnection Connection type pipe Maximum length (One way) Maximum height difference INDOOR UNIT 49 50 Refrigerant control 15*1 6 RAS-13UKP-ES3, AS3 275 790 208 10 Finned tube Cross flow fan mm mm mm kg Width Depth m3/h m /h 3 630 520 430 650 550 490 20 Honeycomb woven filter with PP frame RAS-13UAH-ES3, AS3 630 520 430 m3/h W RAS-13UA-ES3, AS3 550 780 270 mm mm mm kg 39 Width Depth 37 Finned tube Propeller fan 2120 2200 42 2120 2200 2030 30 2150 W PA150X2T-4FM1 1100 Fuse, Overload relay Automatic louver -10 ~ 24 15 ~ 43 -3- FILE NO. [. . . ] 8-4-16 NOTE If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall. After passing the connecting pipe through the pipe hole, connect the connecting pipe to the auxiliary pipes and wrap the facing tape around them. Push Push CAUTION Bind the auxiliary pipes (two) and connecting cable with facing tape tightly. In case of leftward piping and rear-leftward piping, bind the auxiliary pipes (two) only with facing tape. Indoor unit Auxiliary pipes Connecting cable Installation plate Fig. 8-4-18 Carefully arrange pipes so that any pipe does not stick out of the rear plate of the indoor unit. Carefully connect the auxiliary pipes and connecting pipes to each other and cut off the insulating tape wound on the connecting pipe to avoid double-taping at the joint, moreover, seal the joint with the vinyl tape, etc. Since dewing results in a machine trouble, make sure to insulate both the connecting pipes. (Use polyethylene foam as insulating material. ) When bending a pipe, carefully do it, not to crush it. NOTE Hole should be made at a slight downward slant on the outdoor side. Do not rise the drain hose. Do not form the drain hose into a wavy shape. 8-5. Installation place A place which provides the spaces around the outdoor unit as shown in the left diagram. A place which can bear the weight of the outdoor unit and does not allow an increase in noise level and vibration. Projection margin in flaring : A (Unit : mm) A Tightening torque of flare pipe connections The operating pressure of R410A is higher than that of R22. It is therefore necessary to firmly tighten the flare pipe connecting sections (which connect the indoor and outdoor units) up to the specified tightening torque. Incorrect connections may cause not only a gas leakage, but also damage to the refrigerant cycle. Flare at indoor unit side Die Pipe Fig. of copper pipe 6. 35 9. 52 12. 70 R410A tool used 0 to 0. 5 0 to 0. 5 0 to 0. 5 Conventional tool used 1. 0 to 1. 5 1. 0 to 1. 5 1. 0 to 1. 5 Flare at outdoor unit side Fig. 8-5-4 Imperial (wing nut type, conventional tool) Outer dia. of copper pipe 6. 35 9. 52 12. 70 <Tightening connection> Align the centers of the connecting pipes and tighten the flare nut as far as possible with your fingers. Then tighten the nut with a spanner and torque wrench as shown in the figure. Half union R410A Mark line 1. 5 to 2. 0 1. 5 to 2. 0 2. 0 to 2. 5 Fig. 8-5-5 Flare nut Externally threaded side Internally threaded side CAUTION Do not apply excess torque. Otherwise, the nut may crack depending on the conditions. Use a wrench to secure. Use a torque wrench to tighten. Fig. 8-5-6 CAUTION KEEP IMPORTANT 4 POINTS FOR PIPING WORK (1) Take away dust and moisture (Inside of the connecting pipes. ) (2) Tight connection (between pipes and unit) (3) Evacuate the air in the connecting pipes using VACUUM PUMP. (4) Check gas leak (connected points) - 45 - FILE NO. [. . . ] 2) Remove the 2 screws fixing the base bearing. 3) Remove the bearing from the base bearing. If the housing protrudes from the base bearing, put the housing in position and attach the bearing to the base bearing. 2 2-Screws - 68 - FILE NO. Part name Procedures Remarks 1 Common procedure Cord clamp 2-Screws 4 x 22L 1) Stop the operation of air-conditioner, and disconnect the power cord from the AC Electric parts cover supply. [. . . ]