User manual TOSHIBA SATELLITE PRO P100 (PSPAE)

[. . . ] TOSHIBA AMERICA INFORMATION SYSTEMS, INC. ("TOSHIBA"), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA, NETWORK SYSTEMS OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. Protection of Stored Data For your important data, please make periodic back-up copies of all the data stored on the hard disk or other storage devices as a precaution against possible failures, alteration, or loss of the data. IF YOUR DATA IS ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. [. . . ] If you change the Country/Region in the Control Panel, the change may not take effect. NOTE 134 2 Exploring Your Computer's Features Setting up for communications The Region Selection icon will appear in the Task Bar. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. Select a region from the region menu or a telephony location from the sub-menu. 3 When you click a region it becomes the modem's region selection, and the New Location for telephony will be set automatically. When you select a telephony location, the corresponding region is automatically selected and it becomes the modem's current region setting. Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Settings You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection A submenu appears displaying location information for telephony. Exploring Your Computer's Features Setting up for communications 135 Open dialog box, if the modem and Telephony Current Location region code do not match A warning dialog box is displayed if current settings for region code and telephony location are incorrect. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties. NOTE If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting the modem to a telephone line Your computer comes with a built-in modem (available on certain models) that can be connected to a standard voicegrade telephone line. The modem allows you to: Access the Internet. Check with your LAN administrator before disconnecting from the hub. Accessing a network To access a network: At the office, connect an Ethernet cable to the RJ45 jack on your computer. For specific information about connecting to the network, consult your network administrator. While you are at home or traveling, you need a dial-up connection. Ask your network administrator for the telephone number of the network. Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To set up a dial-up connection, use the New Connection Wizard: 1 2 3 Click Start, and then All Programs. Click Accessories, Communications, and click New Connection Wizard. Enter the phone number of your network connection and let the program dial the number. The computer connects to the network. 140 Exploring Your Computer's Features Setting up for communications How to disable the Ethernet LAN port When your computer starts, Windows attempts to contact a Dynamic Host Configuration Protocol (DHCP) server. If the computer is not connected to a network, it may pause a few minutes as it waits for a reply. To avoid this delay, you can reconfigure Windows to disable the LAN port. To disable the LAN port: 1 2 3 4 5 6 7 Click Start, Control Panel, and then Performance and Maintenance. [. . . ] To reset the computer by reloading the operating system without turning the computer off. RJ11 -- A modular connector used on most U. S. telephone systems and direct-connect modems. The RJ11 connector is a 6-wire connector. [. . . ]