User manual TOSHIBA SATELLITE C660D

[. . . ] All tasks covered in this guide can be performed by a field technician without jeopardizing your notebook's warranty. For information on your notebook's general maintenance, technical support, safety notices, and regulatory notices, see your Gateway user's guide. If you have suggestions regarding the content of this guide, send an e-mail with the subject "Service Guide Comments" to channel. services@gateway. com. © 2002 Gateway, Inc. Gateway, Gateway Country, the Gateway stylized logo, and the black-and-white spot design are trademarks or registered trademarks of Gateway, Inc. [. . . ] (The screw cannot be removed. ) Screw 18 www. gateway. com Replacing the hard drive kit 4 Lift the screw side of the cover upward, then slide the cover out. 5 Pull on the metal flange to disconnect the hard drive kit from the connector. Flange www. gateway. com 19 Replacing Components in Your Gateway SATELLITE C660D 6 Lift the plastic tab on the hard drive kit, then lift the kit out of your notebook. Tab 7 Place the new hard drive kit into the drive bay, then slide the drive onto the connector. 8 Replace the cover and tighten the screw. 20 www. gateway. com Replacing the hard drive in the hard drive kit Replacing the hard drive in the hard drive kit Tools you need to complete this task: Phillips #0 screwdriver Screws removed during this task: 4 chrome 3 × 3. 5 mm (hard drive) To install a new hard drive into the kit: 1 2 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Remove the hard drive kit by following the instructions in "Replacing the hard drive kit" on page 18. www. gateway. com 21 Replacing Components in Your Gateway SATELLITE C660D 3 Remove the four screws that secure the hard drive to the hard drive kit bracket. Screw Screw Bracket Screw Screw 4 Remove the old drive from the bracket. 22 www. gateway. com Replacing the hard drive in the hard drive kit 5 Insert the new drive into the bracket so the screw holes line up, then replace the four screws that secure the drive to the bracket. Screw Screw Bracket Screw Screw 6 Place the new hard drive kit into the drive bay, then slide the drive onto the connector. 7 Replace the cover and tighten the screw. www. gateway. com 23 Replacing Components in Your Gateway SATELLITE C660D Replacing the keyboard cover Tools you need to complete this task: Flat-blade screwdriver To replace the keyboard cover: 1 2 3 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Be careful not to damage the LCD panel. Tabs 10 11 12 Carefully press the keyboard down until it is flat all the way across. The keyboard should fall into place easily. If a grounding strap that was connected to the far-right screw, make sure to reconnect it. Reassemble your notebook. 30 www. gateway. com Replacing the hinge covers Replacing the hinge covers Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 4 chrome 2. 5 × 5 mm (hinge covers) To replace the hinge covers: 1 2 3 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Open the LCD panel all the way, so it lies flat on the table. www. gateway. com 31 Replacing Components in Your Gateway SATELLITE C660D 4 Remove the four screws that secure the hinge covers to your notebook. Screws Screws 5 Lift the hinge covers off the hinges. 6 7 Snap the new covers into place over the hinges, then replace the four screws. Reassemble your notebook. 32 www. gateway. com Replacing the LCD panel assembly Replacing the LCD panel assembly Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 4 chrome 2. 5 × 5 mm (hinge covers) 4 or 6 chrome 2. 5 × 7 mm (LCD panel hinges) To replace the LCD panel assembly: 1 2 3 4 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. If your notebook has 802. 11 wireless networking built in, remove the 802. 11 Mini PCI module by following the instructions in "Replacing the 802. 11 Mini PCI card" on page 13. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Pull up on the touchpad connector tabs to make sure that the connector is in the raised position. Slide the end of the touchpad cable into the touchpad connector. Use two fingers to press down on the touchpad connector tabs. This locks the touchpad cable into the touchpad connector. Reassemble your notebook. www. gateway. com 43 Replacing Components in Your Gateway SATELLITE C660D Replacing the cooling assembly Tools you need to complete this task: Phillips #0 screwdriver Flat-blade screwdriver Screws removed during this task: 5 chrome 2. 5 × 4 mm (keyboard) 4 chrome 2. 5 × 5 mm (hinge covers) 4 or 6 chrome 2. 5 × 7 mm (LCD panel hinges) 13 chrome 2. 5 × 5 mm (bottom) 4 chrome 2. 5 × 5 mm (back) 1 chrome 2. 5 × 7 mm (near touchpad) 1 chrome 2. 5 × 4 mm (near multifunction buttons) (palm rest) To replace the cooling assembly: 1 2 3 4 Disconnect the power cord, remove the main and optional secondary battery, and prepare your notebook by following the instructions in "Preparing your work space" on page 3. If your notebook has 802. 11 wireless networking built in, remove the Mini PCI module by following the instructions in "Replacing the 802. 11 Mini PCI card" on page 13. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Remove the keyboard by following the instructions in "Replacing the keyboard" on page 26. 44 www. gateway. com Replacing the cooling assembly 5 6 7 8 Remove the hinge covers by following the instructions in "Replacing the hinge covers" on page 31. Remove the LCD panel by following the instructions in "Replacing the LCD panel assembly" on page 33. Remove the palm rest assembly by following the instructions in "Replacing the palm rest assembly" on page 39. Unplug the cooling fan. www. gateway. com 45 Replacing Components in Your Gateway SATELLITE C660D 9 Loosen the four captive screws that secure the cooling assembly to your notebook. [. . . ] If your notebook has 802. 11 wireless networking built in, remove the Mini PCI module by following the instructions in "Replacing the 802. 11 Mini PCI card" on page 13. Remove the keyboard cover by following the instructions in "Replacing the keyboard cover" on page 24. Remove the keyboard by following the instructions in "Replacing the keyboard" on page 26. Remove the hinge covers by following the instructions in "Replacing the hinge covers" on page 31. [. . . ]