User manual TOSHIBA SATELLITE PRO L870

[. . . ] · Has the battery power of your CLIÉ handheld run out?Place your CLIÉ handheld on the charger cradle connected to the AC power adapter, then allow it to be charged for a few minutes before turning it on. If it turns on, continue charging for approximately four hours and then perform a soft reset. My CLIÉ handheld does not respond Is the POWER/HOLD switch of your CLIÉ handheld in HOLD mode?Your CLIÉ handheld does not work when the POWER/HOLD switch is in HOLD mode. [. . . ] B If you are using Windows 98 Second Edition/Windows Me, click (HotSync) in the task tray at the bottom right of your computer window and click [Local] in the Setup window. Then ensure [Serial Port] of the simulated port for IR communication is selected. B Ensure [Local] and [IR to a PC/handheld] are selected in the HotSync screen on your CLIÉ handheld. B Point the IR port of your CLIÉ handheld directly to the IR port of your computer. The distance between the IR ports of your CLIÉ handheld and your computer, should be 4 to 8 inches (approximately 10 to 20 centimeters). The optimum distance for beaming may vary depending on devices. B You cannot perform the IR HotSync® operation if the remaining battery power is inadequate. After charging the battery of your CLIÉ handheld, try the IR HotSync® operation again. Tap [IR to a PC/Handheld] in [Connection] of Preferences. Then tap [Edit. . . ], [Details. . . ] and specify [Speed:] in the Details screen. Continued on next page ···················· 27 If you still cannot perform the HotSync® operation If you cannot solve your HotSync® operation problem by following the troubleshooting tips in this manual, follow the procedure below. Check if any "Unknown device" is listed in the Device Manager on your computer. 1 2 3 4 Right-click [My Computer] and select [Properties] from the menu. The System Properties window is displayed. If you are using Windows 2000 Professional/Windows XP, click [Hardware]. Check if there is a device marked with or . A device with such mark is not operating normally. Especially, add-on applications installed via infra-red beaming or via "Memory stick" media cannot be backed up using the HotSync® operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I cannot connect to the Internet I cannot connect to the Internet via a wireless LAN (for SATELLITE PRO L870 only) B Check that [SSID:] is correctly selected in the Wireless LAN Setup screen, which can be displayed by tapping [Network]-[V Service][Wireless LAN]-[Details. . . ] in Preferences. Continued on next page ···················· 31 I cannot connect to the Internet via a wireless LAN (for SATELLITE PRO L870 only) B Check that the settings for [SSID:] or [WEP Key:] are correct in the SSID Setup screen, which can be displayed by tapping [Edit. . . ] from [SSID] in the menu of the Wireless LAN Setup screen. B Your CLIÉ handheld may be connected to a wireless LAN access point other than the target one when [-Auto Connect-] is selected. In the Wireless LAN Setup screen, check that the target wireless LAN access point is listed just below [-Auto Connect-] and [-Auto Connect-] is selected. (The list can be reordered by tapping or . ) You can also select the SSID for the target wireless LAN access point instead of selecting [-Auto Connect-] from [SSID:] in order to explicitly connect to the target one. B The channel setting must be channels 1-11 for the wireless LAN access point. Change the channel setting for an appropriate channel. b For details on setup, refer to the manual of the wireless LAN access point. B Your CLIÉ handheld and the wireless LAN access point may be too far away. You need to be closer to the wireless LAN access point when trying to connect to it. B Some obstacles, such as metal plate or concrete, are in the way between your CLIÉ handheld and the wireless LAN access point. Move your CLIÉ handheld or the wireless LAN access point to find the best reception, or do not select [Power Save:] in the SSID Setup screen. [. . . ] Wipe the terminal with a soft cloth, such as a cotton pad. B You cannot use "Memory Stick" media that is formatted in a device other than your CLIÉ handheld. B When the battery power of your CLIÉ handheld is running low, data on storage media, such as "Memory Stick" media may not be displayed. Charge the battery of your CLIÉ handheld. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I cannot transfer data I cannot transfer image files or movie files from my computer to my CLIÉ handheld B Use Image Converter to transfer image files or movie files from your computer to your CLIÉ handheld. [. . . ]