User manual TOSHIBA SD-100X

[. . . ] DIGITAL VIDEO DVD VIDEO PLAYER SD-100X Sep. , 2000 s Introduction SAFETY PRECAUTIONS WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR AVIS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] To enjoy DTS Digital SurroundTM playback, an external 5. 1 channel DTS Digital SurroundTM decoder system must be connected to the BITSTREAM/PCM AUDIO OUT jack of the DVD video player. Connecting to an amplifier equipped with an MPEG2 audio decoder Connections MPEG2 sound You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with an MPEG2 audio decoder or MPEG2 audio processor. VIDEO OUT VIDEO Y PB PR · Use DVD video discs encoded via the MPEG2 recording system. · Make the following setting. AUDIO OUT Amplifier equipped with an MPEG2 audio decoder 75 coaxial cable To digital audio input S R L ANALOG BITSTREAM/ PCM On-screen display "Audio Out Select" Recording system Select: "Bitstream" MPEG Page 35 39 33 To BITSTREAM/PCM AUDIO OUT Connecting to an amplifier equipped with a digital audio input 2 channel digital stereo You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker system (right and left front speakers). VIDEO OUT VIDEO Y PB PR · Make the following setting. Amplifier equipped with a digital audio input AUDIO OUT S R L ANALOG BITSTREAM/ PCM On-screen display "Audio Out Select" Select: "PCM" Page 35 39 To BITSTREAM/PCM AUDIO OUT 75 coaxial cable To digital audio input Notes · DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video player to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO OUT jack of the DVD video player. · Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD video player to the "COAXIAL" input of a Receiver or Processor. · Refer to the owner's manual of the connected equipment as well. · When you connect the DVD video player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. · The output sound of the DVD video player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level. Otherwise, the speakers may be damaged by a sudden high volume sound. · Turn off the amplifier before you connect or disconnect the DVD video player's power cord. If you leave the amplifier power on, the speakers may be damaged. 19 Basic playback Playing a Disc This section shows you the basics on how to play a disc. CAUTION Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury. ON/STANDBY indicator 3 PAUSE STOP PLAY PAUSE STOP ON/STANDBY OPEN/CLOSE SKIP 1 DVD VCD CD 2 4 Basic playback Preparations · When you want to view a disc, turn on the TV and select the video input connected to the DVD video player. · When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input connected to the DVD video player. 1 Press ON/STANDBY. ON/STANDBY Initial set-up Make the following settings on the display. On-Screen Language: Select the appropriate on-screen language. TV Shape: Select a picture size according to the aspect ratio of your TV. (See 38 for details. ) TOSHIBA Thank you for your purchase of this TOSHIBA DVD Player. Please make a selection for On-Screen Language and your TV Shape and press ENTER button on your remote control. FIRST SETUP On-Screen Language TV Shape The DVD video player turns on and the ON/STANDBY indicator on the player illuminates. When the DVD video player is turned on for the first time, an initial set-up display appears. See "Initial set-up" and make the proper settings before proceeding to step 2. ENG 4:3LB 2 3 Press OPEN/CLOSE. OPEN/CLOSE The disc tray opens. 1 Press / to select "On-Screen Language, " and press ENTER. 2 Select a language using / , and press ENTER. 3 Press to select "TV Shape, " and press ENTER. [. . . ] · Place the disc correctly inside the guide on the disc tray. · Cancel the parental lock function or change the parental lock level. · These operations may prevent a proper progress of the contents. · Turn the power on or off with the ON/ STANDBY button. [. . . ]