User manual TOSHIBA SD-4015-KE

[. . . ] Introduction 2 DIGITAL VIDEO Connections 14 DVD PLAYER Basic playback 19 SD4015KE OWNER'S MANUAL Function setup 23 Others 27 © 2010 Toshiba Corporation Introduction SAFETY PRECAUTIONS The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: VISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM. AVIS WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this owner's manual. CLASS 1 LASER PRODUCT The symbol for Class (Double lnsulation) WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. [. . . ] HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. Connecting to a display (Using a HDMITM cable) Connections VIDEO L HDMI OUT COAXIAL DIGITAL ANALOG R To HDMI Output HDMI Cable Available output signals are below: · Auto · 576p/480p (progressive) · 720p (progressive) · 1080i (interlaced) · 1080p (progressive) (not supplied) HDMI-compatible display · Make the following setting. On-screen display "Digital out" "Video" Select: "PCM" HDMI Page 24 Switching the video quality (HDMI mode) using HDMI button on the remote control or HDMI SELECT button on the front panel. Press HDMI button on the remote control or HDMI SELECT button on the front panel to receive a suitable video quality. The video quality is required to match your TV having HDMI feature and suitable quality. Please also check your TV owner's manual. Press this button to change the output signals as below. See the HDMI indicator and select the appropriate output signal. HDMI indicator Video output signal 24 1080p (progressive) illuminates " · 1080p " Press 1080i (interlaced) illuminates " · 1080i " Press 720p (progressive) illuminates " · 720p " Press illuminates " · 576p/480p " 576p/480p (progressive) Press illuminates "· 576p/480p, · 720p, · 1080i, · 1080p" Press Auto 576p/480p, 720p, 1080i and 1080p are signals created with this DVD Player from original 576i/480i signal. The resolution of the picture may not be increased even if they are selected. Notes · Refer to the owner's manual of the connected TV as well. · When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any connections. · If you have a HDMI (with HDCP) equipped monitor or display, you can connect it to this player using a HDMI cable. · The HDMI connector outputs uncompressed digital video, as well as almost every kind of digital audio that the player is compatible with, including DVD-Video, Video CD/Super VCD, CD, MP3 and DivX®. · This unit has been designed to be compliant with HDMI (High Definition Multimedia Interface) depending on the component you have connected. Using a HDMI connection may result in unreliable signal transfers. · Because HDMI is an evolving technology, it is possible that some devices with an HDMI input may not operate properly with this DVD player. · When using HDMI cable, do not connect to other analog video outputs. · HDMI output is only available when the Video out is set to "HDMI". Otherwise the HDMI button is invalid. 15 Connections Content of the output for each output jack is shown in the following table and differ depending on the On-Screen Display Setting: On-Screen Display Setting "Video" Setting RGB HDMI Output Setting Invalid 576p/480p HDMI 720p 1080i 1080p Content of output for each output jack HDMI Output 576p/480p 720p 1080i 1080p Video Output Composite Composite Composite Composite Composite AV Output RGB Composite Composite Composite Composite * Settings for HDMI output format are performed using the HDMI button on the remote control or HDMI SELECT button on the front panel. Note · If Auto is selected, it follows preference HDMI aspect ratio of TV. Connecting to Optional Equipment You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment. · For connection to your TV, see "Connecting to a TV" . · This section uses the following reference marks. : Front speaker : Rear speaker : Sub woofer : Center speaker : Signal flow Warning · When you are connecting (via the COAXIAL DIGITAL AUDIO OUT jack) an AV decoder that does not have Dolby Digital, DTS® or MPEG2 decoding function, be sure to set "Digital out" to "PCM" from the on-screen displays. Otherwise, high volume sound may damage your hearing as well as the speakers. · When playing DTS-encoded discs (DVDs and audio CDs), excessive noise may be output from the analog audio output jacks. To avoid possible damage to the audio system, you should take proper precautions when the analog audio output jacks of the DVD player are connected to an amplification system. To enjoy DTS Digital SurroundTM playback, an external 5. 1 channel DTS Digital SurroundTM decoder system must be connected to the COAXIAL DIGITAL AUDIO OUT jack of the DVD player. Notes · DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack of the DVD player. · Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the "DIGITAL (COAXIAL)" input of a Receiver or Processor. [. . . ] · Press and hold the ON/STANDBY button on the front panel for more than about 3 seconds. If the buttons still do not work, disconnect the power plug and insert it into the wall outlet again. · Point the remote control at the remote sensor of the DVD player. · Operate the remote control within about 7 m. [. . . ]