User manual TOSHIBA TDP-MT200

[. . . ] English Français Español Deutsch Italiano Português Svenska OWNER'S MANUAL DLPTM PROJECTOR Others Maintenance Operations Preparations TDP-MT200 Before Using Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] If such is a case, decrease your computer's refresh rate or the resolution. It is also recommended to use a DVI cable in 2 m or less in length. 20 English Français Español Deutsch Italiano Português Svenska Connecting the power cord 1 2 Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or other power outlet. Power cord connector (Supplied) Removing the lens cover Turning the power on 1 Turn on the main power switch The ON indicator will change to orange, indicating standby mode. · After the main power switch is turned on, the inner cooling fan starts cooling. (Orange) 2 Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON, LAMP, and FAN. After a moment, the start-up screen appears. Control panel Remote Control Start-up screen CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. 21 Preparations Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. Turning the power on and off (Continued) Notes · The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p. 30 . · The first time you use the projector after purchase, after the start-up screen disappears, the Language menu is displayed p. 23 . Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears. ) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. When cooling lamp During internal cooling After cooling complete A (Green) Flashing (Orange) (Green) (Off) (Green) (Off) (Off) B (Orange) C (Orange) A B During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. After the LAMP indicator goes off, the cooling fan continues to operate for a short while, in order to expel excess internal heat. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state. In standby mode C Note · The projector consumes about 12W of power in standby. We recommend that you unplug the power cord or turn off the main power switch if you will not be using the projector for an extended period. PRECAUTION · If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. [. . . ] p. 18 Is the remote control being used within the effective range?p. 18 Are there any obstructions between the remote control and projector?· Are there any fluorescent or other bright lights shining at the projector's infrared remote sensor?· · · · 37 Others Specifications List of general specifications Item Consumption Power Weight External Dimensions (including protruding parts) Cabinet material* Conditions for usage environment Display pixels Picture elements Lens Lamp Projection screen size Projection distance COMPUTER terminal DVI-D terminal Y terminal PB/CB terminal PR/CR terminal VIDEO terminal S-VIDEO terminal CONTROL terminal Specification 300 W 2. 8 kg 298 × 101. 4 × 275. 4 mm (W × H × D) PC+ABS resin and ABS resin Temp: 5°C to 35°C; relative humidity: 30% to 70% 1 chip DMDTM 409, 920 pixels (854H × 480V) Zoom lens F=2. 75-3. 03 f=22. 3-26. 76 mm High-pressure mercury lamp 24-290 inches 1. 20-12. 00m Mini D sub 15 pin Analog RGB DVI connector Digital RGB RCA Pin Jack, 1V(p-p), 75 RCA Pin Jack, 0. 7V(p-p), 75 RCA Pin Jack, 0. 7V(p-p), 75 RCA Pin Jack, 1 V (p-p), 75 Mini DIN 4 pin Mini DIN 8 pin (RS-232C) Connection terminal Note · This model complies with the above specifications. [. . . ]