User manual TOSHIBA TDP-T95

[. . . ] TDP-T95 TDP-T100 OWNER'S MANUAL DATA PROJECTOR Others Maintenance Operations Preparations Before Using Before Using SAFETY PRECAUTIONS Before Using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. [. . . ] If it is left on, it could become deformed due to heat. A message appears on the screen, confirming that you wish to shut off the power. This message will disappear after a moment. (This operation is no longer valid after the message disappears. ) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short while. Then, the projector goes into standby mode. When cooling lamp During internal cooling After cooling complete Turning the power on Press the ON/STANDBY button. The power turns on, and the following 3 green indicators light: ON/STANDBY, LAMP, and FAN. After a moment, the start-up screen appears. Control panel Remote Control Start-up screen A B C A During cooling, the LAMP indicator flashes. In this state, the power cannot be turned back on. If you are in a hurry, there is no problem with unplugging the power cord in this state. After the LAMP indicator goes off, the FAN indicator keeps lighted and the cooling fan continues to operate for a short while, in order to expel excess internal heat. In standby mode B CAUTION · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. C Note · The projector consumes about 9W of power in standby. We recommend that you unplug the power cord if you will not be using the projector for an extended period. PRECAUTION · If the power cord is unplugged before cooling is complete, give the lamp time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may fail to light. 24 25 Operations Basic operations 1 Turn on the power. Turn on the power by following the instructions in "Turning the power on" p. 24 . 5 Projector placement angle adjustments The placement angle and the height of the projected image can be adjusted by the foot adjuster. 2 Select the language and the lamp power (When using the first time). When the projector is used for the first time after purchase, the start menu for language (to display the menus and messages on the screen) and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 . ) q Lift up the front of the projector to the desired angle, then press the foot adjuster release button. The foot adjuster extends. Release the button to lock the position. 1 q Use the or button to select the desired language and press the button. Message for setup confirmation is displayed in a selected language. Then, the menu for lamp power selection and configuration is displayed. To change the setting, follow the step w. w Use the or button to select the lamp power and press the button. The lamp power, if selected, will be toggled without pressing the button. The display automatically disappears in a few seconds. Notes · When the projector is turned on the next time, the start menu does not appear upon startup. [. . . ] p. 21 Are the sharpness or sampling phase adjustments off?p. 35 p. 21 Image is dark Colors too light Bad shading · Are the brightness or contrast adjustments off?p. 35 · Is the lamp nearing the end of its service life?p. 42 · · · · Are the color, R-level, G-level, or B-level adjustments off? [. . . ]