User manual TOSHIBA TP48C51

[. . . ] 25 Navigating pages using LIST . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 PROBLEM SOLVING Questions and Answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 INFORMATION Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or to tune-in a station on another System. Use Y and y to move across the screen and select any of these Manual Tune options. Manual tuning System 0 OK a Press M and using Y or y select the SET UP menu, with < highlight Manual tuning, press Q to select. SET UP Language Country Auto tuning English UK OK OK OK OK EXIT I A C 60 0 VCR Manual tuning AV connection Store MENU Back EXIT Watch TV Picture position MENU Back Watch TV 12 345 6 7 1 2 3 8 Programme: The number to be pressed on the remote control. Colour system: Factory set to Auto, should only be changed if problems are experienced, i. e. Programme skip: 8 means nothing has been stored or the facility to skip the channel is ON. See page 13. b Use > or < to highlight the programme position required e. g. 0 for a media recorder. Manual tuning Prog. 0 1 2 3 4 5 OK Channel C60 C22 C28 C25 C32 C69 Station BBC1 BBC2 ITV CH4 4 5 6 7 Channel: The channel number on which a station is being broadcast. Search: Search up and down for a signal. Manual fine tuning: Only used if interference/weak signal is experienced. Use the > or < and Y or y buttons to enter up to seven characters. MENU Select Back Sort EXIT Watch TV Different Channel numbers may be displayed. c Press Q to select. If the programme is skipped, Programme skip must be removed before storing. Manual tuning System 0 OK 8 I A C 60 0 To allocate a programme position on the television for a decoder and media recorder: turn the decoder on, insert a pre-recorded film in the media recorder and press PLAY, then manually tune. Store MENU Back EXIT Watch TV d e f Press y to select System and use > or < to change if required. When the search is complete the television will automatically select programme position 1. This may not be a clear picture, so the station order can be changed using Manual tuning, see page 12. 14 00GB_TP48C51P_EngOM. book Page 15 Tuesday, December 11, 2007 5:40 AM CONTROLS AND FEATURES General controls Selecting programme positions To select a programme position use the numbered buttons on the remote control. Programme positions can also be selected using > and <. To revert to the previous programme position press . Bass, Treble and Balance a Press M and Y or y to select SOUND. SOUND Dual Bass Treble Balance Bass boost Dual 1 0 0 0 On 70 EXIT To display on-screen information i. e. programme position, input mode or stereo/mono signal, press . Press again to cancel. The Time Display The time display facility allows the current (text service) time to be seen on the television screen. Press D whilst watching a normal television broadcast to see a time display from the broadcaster. It will remain on screen for about 5 seconds. Bass boost level MENU Back Watch TV b Press < to highlight Bass, Treble or Balance and Y or y to change the setting. Bass boost Stereo and Bilingual transmissions If stereo or dual language broadcasts are transmitted the word Stereo or Dual will appear on the screen each time programme positions are changed, disappearing after a few seconds. If the broadcast is not in stereo the word Mono will appear. If they are transmitted the word Dual will display. Choose the required programme number and if the word Dual appears press s to select Dual 1, Dual 2 or Mono. [. . . ] The news flash page must be cancelled before changing programmes. Remember to cancel text before changing channels - press the button twice. 26 00GB_TP48C51P_EngOM. book Page 27 Tuesday, December 11, 2007 5:40 AM PROBLEM SOLVING Questions and Answers Below are the answers to some of the most common queries. For more information go to www. toshiba. co. uk Q A Q A a Why is there no sound or picture? Check the television is not in standby mode. Check the mains plug and all mains connections. Q A Q A a b Why is the VCR/DVD picture in black and white? Check the correct input has been chosen, S-VIDEO or AV. See AV connections page 23. What else can cause a poor picture? Interference or a weak signal. [. . . ]